Difference between revisions of "RFC5994"
imported>Admin (Created page with " Internet Engineering Task Force (IETF) S. Bryant, Ed.Request for Comments: 5994 M. MorrowCategory: Informational ...") |
|||
Line 1: | Line 1: | ||
+ | Internet Engineering Task Force (IETF) S. Bryant, Ed. | ||
+ | Request for Comments: 5994 M. Morrow | ||
+ | Category: Informational G. Swallow | ||
+ | ISSN: 2070-1721 Cisco Systems | ||
+ | R. Cherukuri | ||
+ | Juniper Networks | ||
+ | T. Nadeau | ||
+ | Huawei Technologies | ||
+ | N. Harrison | ||
+ | BT | ||
+ | B. Niven-Jenkins | ||
+ | Velocix | ||
+ | October 2010 | ||
+ | Application of Ethernet Pseudowires to MPLS Transport Networks | ||
− | + | '''Abstract''' | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | Abstract | ||
Ethernet pseudowires are widely deployed to support packet transport | Ethernet pseudowires are widely deployed to support packet transport | ||
Line 28: | Line 35: | ||
of MPLS-TP. | of MPLS-TP. | ||
− | Status of This Memo | + | '''Status of This Memo''' |
This document is not an Internet Standards Track specification; it is | This document is not an Internet Standards Track specification; it is | ||
Line 38: | Line 45: | ||
Internet Engineering Steering Group (IESG). Not all documents | Internet Engineering Steering Group (IESG). Not all documents | ||
approved by the IESG are a candidate for any level of Internet | approved by the IESG are a candidate for any level of Internet | ||
− | Standard; see Section 2 of | + | Standard; see Section 2 of RFC 5741. |
− | |||
− | |||
− | |||
− | |||
Information about the current status of this document, any errata, | Information about the current status of this document, any errata, | ||
Line 48: | Line 51: | ||
http://www.rfc-editor.org/info/rfc5994. | http://www.rfc-editor.org/info/rfc5994. | ||
− | Copyright Notice | + | '''Copyright Notice''' |
Copyright (c) 2010 IETF Trust and the persons identified as the | Copyright (c) 2010 IETF Trust and the persons identified as the | ||
document authors. All rights reserved. | document authors. All rights reserved. | ||
− | This document is subject to | + | This document is subject to BCP 78 and the IETF Trust's Legal |
Provisions Relating to IETF Documents | Provisions Relating to IETF Documents | ||
(http://trustee.ietf.org/license-info) in effect on the date of | (http://trustee.ietf.org/license-info) in effect on the date of | ||
Line 86: | Line 89: | ||
explained in this document are also recognized by the MPLS transport | explained in this document are also recognized by the MPLS transport | ||
profile (MPLS-TP) design effort formed jointly by the IETF and ITU-T | profile (MPLS-TP) design effort formed jointly by the IETF and ITU-T | ||
− | [RFC5654]. For example, the ability to operate solely with network | + | [[[RFC5654]]]. For example, the ability to operate solely with network |
management control, the ability to use Operations, Administration, | management control, the ability to use Operations, Administration, | ||
and Maintenance (OAM) that does not rely on IP forwarding, and the | and Maintenance (OAM) that does not rely on IP forwarding, and the | ||
Line 108: | Line 111: | ||
on sound foundations. | on sound foundations. | ||
− | Much of the notation used in this document is defined in [RFC3985] to | + | Much of the notation used in this document is defined in [[[RFC3985]]] to |
which the reader is referred for definitions. | which the reader is referred for definitions. | ||
The architecture required for this mechanism is illustrated in Figure | The architecture required for this mechanism is illustrated in Figure | ||
1. | 1. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
+----------------------------------------------------------------+ | +----------------------------------------------------------------+ | ||
Line 175: | Line 164: | ||
MPLS PSN are labeled as the server in Figure 1. In the remainder of | MPLS PSN are labeled as the server in Figure 1. In the remainder of | ||
this document, call the server network a transport network. | this document, call the server network a transport network. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
=== Requirements Language === | === Requirements Language === | ||
Line 185: | Line 169: | ||
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", | The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", | ||
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this | "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this | ||
− | document are to be interpreted as described in [[RFC2119 | + | document are to be interpreted as described in RFC 2119 [[[RFC2119]]]. |
== PWE3 Configuration == | == PWE3 Configuration == | ||
The PWE3 encapsulation used by this specification to satisfy the | The PWE3 encapsulation used by this specification to satisfy the | ||
− | transport requirement is Ethernet [RFC4448]. This is used in "raw" | + | transport requirement is Ethernet [[[RFC4448]]]. This is used in "raw" |
mode. | mode. | ||
Line 196: | Line 180: | ||
The use of the Pseudowire Setup and Maintenance Label Distribution | The use of the Pseudowire Setup and Maintenance Label Distribution | ||
− | Protocol [RFC4447] is not required by the profile of the PWE3 | + | Protocol [[[RFC4447]]] is not required by the profile of the PWE3 |
Ethernet pseudowire functionality defined in this document. | Ethernet pseudowire functionality defined in this document. | ||
Line 220: | Line 204: | ||
as Virtual Circuit Connectivity Verification (VCCV)) is NOT | as Virtual Circuit Connectivity Verification (VCCV)) is NOT | ||
vulnerable to the above failure mode. For these reasons, the OAM | vulnerable to the above failure mode. For these reasons, the OAM | ||
− | mechanism is as described in [RFC5085], which uses Bidirectional | + | mechanism is as described in [[[RFC5085]]], which uses Bidirectional |
− | Forwarding Detection (BFD) [RFC5880] for connection verification | + | Forwarding Detection (BFD) [[[RFC5880]]] for connection verification |
(CV). The method of using BFD as a CV method in VCCV is described in | (CV). The method of using BFD as a CV method in VCCV is described in | ||
− | [RFC5885]. One of the VCCV profiles described in Section 3.1 or | + | [[[RFC5885]]]. One of the VCCV profiles described in Section 3.1 or |
Section 3.2 MUST be used. Once a VCCV control channel is provisioned | Section 3.2 MUST be used. Once a VCCV control channel is provisioned | ||
and the operational status of the PW is UP, no other profile should | and the operational status of the PW is UP, no other profile should | ||
be used until such time as the PW's operational status is set to | be used until such time as the PW's operational status is set to | ||
DOWN. | DOWN. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
=== VCCV Profile 1: BFD without IP/UDP Headers === | === VCCV Profile 1: BFD without IP/UDP Headers === | ||
Line 240: | Line 219: | ||
The connection verification method used by VCCV is BFD with | The connection verification method used by VCCV is BFD with | ||
− | diagnostics as defined in [RFC5885]. | + | diagnostics as defined in [[[RFC5885]]]. |
− | [RFC5085] specifies that the first nibble is set to 0x1 to indicate a | + | [[[RFC5085]]] specifies that the first nibble is set to 0x1 to indicate a |
− | channel associated with a pseudowire [RFC4385]. | + | channel associated with a pseudowire [[[RFC4385]]]. |
The Version and the Reserved fields are set to zero, and the Channel | The Version and the Reserved fields are set to zero, and the Channel | ||
Type is set to 0x7 to indicate that the payload carried is BFD | Type is set to 0x7 to indicate that the payload carried is BFD | ||
− | without IP/UDP headers, as is defined in [RFC5885]. | + | without IP/UDP headers, as is defined in [[[RFC5885]]]. |
=== VCCV Profile 2: BFD with IP/UDP Headers === | === VCCV Profile 2: BFD with IP/UDP Headers === | ||
Line 255: | Line 234: | ||
The connection verification method used by VCCV is BFD with | The connection verification method used by VCCV is BFD with | ||
− | diagnostics as defined in [RFC5885]. | + | diagnostics as defined in [[[RFC5885]]]. |
− | [RFC5085] specifies that the first nibble is set to 0x1 to indicate a | + | [[[RFC5085]]] specifies that the first nibble is set to 0x1 to indicate a |
− | channel associated with a pseudowire [RFC4385]. | + | channel associated with a pseudowire [[[RFC4385]]]. |
The Version and the Reserved fields are set to 0, and the Channel | The Version and the Reserved fields are set to 0, and the Channel | ||
− | Type is set to 0x21 for IPv4 and 0x56 for IPv6 payloads [RFC4446]. | + | Type is set to 0x21 for IPv4 and 0x56 for IPv6 payloads [[[RFC4446]]]. |
== MPLS Layer == | == MPLS Layer == | ||
− | The architecture of MPLS-enabled networks is described in [RFC3031]. | + | The architecture of MPLS-enabled networks is described in [[[RFC3031]]]. |
This section describes a subset of the functionality of the MPLS- | This section describes a subset of the functionality of the MPLS- | ||
enabled PSN. There are two cases that need to be considered: | enabled PSN. There are two cases that need to be considered: | ||
Line 274: | Line 253: | ||
Where the use of a control plane is desired, this may be based on | Where the use of a control plane is desired, this may be based on | ||
− | Generalized Multi-Protocol Label Switching (GMPLS) [RFC3945]. | + | Generalized Multi-Protocol Label Switching (GMPLS) [[[RFC3945]]]. |
=== External Configuration === | === External Configuration === | ||
Line 282: | Line 261: | ||
explicitly described in this specification to address the | explicitly described in this specification to address the | ||
− | + | requirements specified by the ITU [[[RFC5654]]] to address the needs in a | |
− | |||
− | |||
− | |||
− | |||
− | requirements specified by the ITU [RFC5654] to address the needs in a | ||
transport environment. | transport environment. | ||
− | The MPLS encapsulation is specified in [RFC3032]. All MPLS labels | + | The MPLS encapsulation is specified in [[[RFC3032]]]. All MPLS labels |
used in the server layer (Figure 1) MUST be statically provisioned. | used in the server layer (Figure 1) MUST be statically provisioned. | ||
Labels may be selected from either the per-platform or the per- | Labels may be selected from either the per-platform or the per- | ||
Line 317: | Line 291: | ||
Both EXP-Inferred-PSC LSPs (E-LSP) and Label-Only-Inferred-PSC LSPs | Both EXP-Inferred-PSC LSPs (E-LSP) and Label-Only-Inferred-PSC LSPs | ||
− | (L-LSP) MUST be supported as defined in [RFC3270]. | + | (L-LSP) MUST be supported as defined in [[[RFC3270]]]. |
− | For the MPLS EXP field [RFC3270] [RFC5462], only the pipe and short- | + | For the MPLS EXP field [[[RFC3270]]] [[[RFC5462]]], only the pipe and short- |
pipe models are supported. | pipe models are supported. | ||
Line 325: | Line 299: | ||
In this section, we describe the control plane configuration when | In this section, we describe the control plane configuration when | ||
− | [RFC3209] or the bidirectional support in GMPLS ([RFC3471] and | + | [[[RFC3209]]] or the bidirectional support in GMPLS ([[[RFC3471]]] and |
− | [RFC3473]) are used to configure the transport MPLS PSN. When these | + | [[[RFC3473]]]) are used to configure the transport MPLS PSN. When these |
protocols are used to provide the control plane, the following are | protocols are used to provide the control plane, the following are | ||
automatically provided: | automatically provided: | ||
1. There is no label merging unless it is deliberately enabled to | 1. There is no label merging unless it is deliberately enabled to | ||
− | support Fast Re-route (FRR) [RFC3209]. | + | support Fast Re-route (FRR) [[[RFC3209]]]. |
2. A single path is provided end-to-end (there is no ECMP). | 2. A single path is provided end-to-end (there is no ECMP). | ||
− | |||
− | |||
− | |||
− | |||
− | |||
3. Label Switched Paths may be unidirectional or bidirectional as | 3. Label Switched Paths may be unidirectional or bidirectional as | ||
Line 346: | Line 315: | ||
support external configuration MUST be applied: | support external configuration MUST be applied: | ||
− | o Penultimate hop popping [RFC3031] by the LSRs MUST be disabled on | + | o Penultimate hop popping [[[RFC3031]]] by the LSRs MUST be disabled on |
LSPs providing PWE3 transport network functionality. | LSPs providing PWE3 transport network functionality. | ||
− | o Both E-LSP and L-LSP MUST be supported as defined in [RFC3270]. | + | o Both E-LSP and L-LSP MUST be supported as defined in [[[RFC3270]]]. |
− | o The MPLS EXP [RFC5462] field is supported according to [RFC3270] | + | o The MPLS EXP [[[RFC5462]]] field is supported according to [[[RFC3270]]] |
only when the pipe and short-pipe models are utilized. | only when the pipe and short-pipe models are utilized. | ||
Line 357: | Line 326: | ||
This document describes a method of using the existing PWE3 Ethernet | This document describes a method of using the existing PWE3 Ethernet | ||
− | pseudowire [RFC4448] to solve a particular network application. The | + | pseudowire [[[RFC4448]]] to solve a particular network application. The |
congestion considerations associated with that pseudowire and all | congestion considerations associated with that pseudowire and all | ||
subsequent work on congestion considerations regarding Ethernet | subsequent work on congestion considerations regarding Ethernet | ||
Line 368: | Line 337: | ||
issues. | issues. | ||
− | The PWE3 security considerations are described in [RFC3985] and the | + | The PWE3 security considerations are described in [[[RFC3985]]] and the |
− | Ethernet pseudowire security considerations of [RFC4448]. | + | Ethernet pseudowire security considerations of [[[RFC4448]]]. |
The Ethernet pseudowire is transported on an MPLS PSN; therefore, the | The Ethernet pseudowire is transported on an MPLS PSN; therefore, the | ||
security of the pseudowire itself will only be as good as the | security of the pseudowire itself will only be as good as the | ||
security of the MPLS PSN. The server MPLS PSN can be secured by | security of the MPLS PSN. The server MPLS PSN can be secured by | ||
− | various methods, as described in [RFC3031]. | + | various methods, as described in [[[RFC3031]]]. |
The use of static configuration exposes an MPLS PSN to a different | The use of static configuration exposes an MPLS PSN to a different | ||
Line 385: | Line 354: | ||
system and the communications paths between those central systems and | system and the communications paths between those central systems and | ||
the LSRs. | the LSRs. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
Security achieved by access control of media access control (MAC) | Security achieved by access control of media access control (MAC) | ||
Line 407: | Line 369: | ||
=== Normative References === | === Normative References === | ||
− | [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate | + | [[[RFC2119]]] Bradner, S., "Key words for use in RFCs to Indicate |
− | + | Requirement Levels", BCP 14, RFC 2119, March 1997. | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
+ | [[[RFC3031]]] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol | ||
+ | Label Switching Architecture", RFC 3031, January 2001. | ||
+ | [[[RFC3032]]] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., | ||
+ | Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack | ||
+ | Encoding", RFC 3032, January 2001. | ||
+ | [[[RFC3209]]] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., | ||
+ | and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP | ||
+ | Tunnels", RFC 3209, December 2001. | ||
+ | [[[RFC3270]]] Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen, | ||
+ | P., Krishnan, R., Cheval, P., and J. Heinanen, "Multi- | ||
+ | Protocol Label Switching (MPLS) Support of Differentiated | ||
+ | Services", RFC 3270, May 2002. | ||
+ | |||
+ | [[[RFC3471]]] Berger, L., "Generalized Multi-Protocol Label Switching | ||
+ | (GMPLS) Signaling Functional Description", RFC 3471, | ||
+ | January 2003. | ||
+ | |||
+ | [[[RFC3473]]] Berger, L., "Generalized Multi-Protocol Label Switching | ||
+ | (GMPLS) Signaling Resource ReserVation Protocol-Traffic | ||
+ | Engineering (RSVP-TE) Extensions", RFC 3473, January 2003. | ||
+ | |||
+ | [[[RFC3945]]] Mannie, E., "Generalized Multi-Protocol Label Switching | ||
+ | (GMPLS) Architecture", RFC 3945, October 2004. | ||
+ | |||
+ | [[[RFC4385]]] Bryant, S., Swallow, G., Martini, L., and D. McPherson, | ||
+ | "Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for | ||
+ | Use over an MPLS PSN", RFC 4385, February 2006. | ||
+ | |||
+ | [[[RFC4446]]] Martini, L., "IANA Allocations for Pseudowire Edge to Edge | ||
+ | Emulation (PWE3)", BCP 116, RFC 4446, April 2006. | ||
+ | |||
+ | [[[RFC4447]]] Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G. | ||
+ | Heron, "Pseudowire Setup and Maintenance Using the Label | ||
+ | Distribution Protocol (LDP)", RFC 4447, April 2006. | ||
+ | |||
+ | [[[RFC4448]]] Martini, L., Rosen, E., El-Aawar, N., and G. Heron, | ||
+ | "Encapsulation Methods for Transport of Ethernet over MPLS | ||
+ | Networks", RFC 4448, April 2006. | ||
+ | |||
+ | [[[RFC5085]]] Nadeau, T. and C. Pignataro, "Pseudowire Virtual Circuit | ||
+ | Connectivity Verification (VCCV): A Control Channel for | ||
+ | Pseudowires", RFC 5085, December 2007. | ||
+ | |||
+ | [[[RFC5462]]] Andersson, L. and R. Asati, "Multiprotocol Label Switching | ||
+ | (MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic | ||
+ | Class" Field", RFC 5462, February 2009. | ||
+ | |||
+ | [[[RFC5880]]] Katz, D. and D. Ward, "Bidirectional Forwarding Detection | ||
+ | (BFD)", RFC 5880, June 2010. | ||
+ | |||
+ | [[[RFC5885]]] Nadeau, T. and C. Pignataro, "Bidirectional Forwarding | ||
+ | Detection (BFD) for the Pseudowire Virtual Circuit | ||
+ | Connectivity Verification (VCCV)", RFC 5885, June 2010. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
=== Informative References === | === Informative References === | ||
− | [RFC3985] Bryant, S. and P. Pate, "Pseudo Wire Emulation Edge-to- | + | [[[RFC3985]]] Bryant, S. and P. Pate, "Pseudo Wire Emulation Edge-to- |
− | [RFC5654] Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., | + | Edge (PWE3) Architecture", RFC 3985, March 2005. |
+ | |||
+ | [[[RFC5654]]] Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., | ||
+ | and S. Ueno, "Requirements of an MPLS Transport Profile", | ||
+ | RFC 5654, September 2009. | ||
+ | |||
Authors' Addresses | Authors' Addresses | ||
Line 441: | Line 447: | ||
EMail: [email protected] | EMail: [email protected] | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
Monique Morrow | Monique Morrow | ||
Line 457: | Line 455: | ||
EMail: [email protected] | EMail: [email protected] | ||
− | |||
George Swallow | George Swallow | ||
Line 465: | Line 462: | ||
EMail: [email protected] | EMail: [email protected] | ||
− | |||
Rao Cherukuri | Rao Cherukuri | ||
Line 473: | Line 469: | ||
EMail: [email protected] | EMail: [email protected] | ||
− | |||
Thomas D. Nadeau | Thomas D. Nadeau | ||
Line 481: | Line 476: | ||
EMail: [email protected] | EMail: [email protected] | ||
− | |||
Neil Harrison | Neil Harrison | ||
Line 487: | Line 481: | ||
EMail: [email protected] | EMail: [email protected] | ||
− | |||
Ben Niven-Jenkins | Ben Niven-Jenkins | ||
Line 496: | Line 489: | ||
EMail: [email protected] | EMail: [email protected] | ||
− | |||
− | |||
− | |||
− | |||
[[Category:Informational]] | [[Category:Informational]] |
Revision as of 03:15, 1 October 2020
Internet Engineering Task Force (IETF) S. Bryant, Ed. Request for Comments: 5994 M. Morrow Category: Informational G. Swallow ISSN: 2070-1721 Cisco Systems
R. Cherukuri Juniper Networks T. Nadeau Huawei Technologies N. Harrison BT B. Niven-Jenkins Velocix October 2010
Application of Ethernet Pseudowires to MPLS Transport Networks
Abstract
Ethernet pseudowires are widely deployed to support packet transport of Ethernet services. These services in-turn provide transport for a variety of client networks, e.g., IP and MPLS. This document uses procedures defined in the existing IETF specifications of Ethernet pseudowires carried over MPLS networks.
Many of the requirements for the services provided by the mechanisms explained in this document are also recognized by the MPLS transport profile (MPLS-TP) design effort formed jointly by the IETF and ITU-T. The solution described here does not address all of the MPLS-TP requirements, but it provides a viable form of packet transport service using tools that are already available.
This document also serves as an indication that existing MPLS techniques form an appropriate basis for the design of a fully- featured packet transport solution addressing all of the requirements of MPLS-TP.
Status of This Memo
This document is not an Internet Standards Track specification; it is published for informational purposes.
This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Not all documents approved by the IESG are a candidate for any level of Internet Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc5994.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English.
Contents
Introduction
Ethernet pseudowires are widely deployed to support packet transport of Ethernet services. These services in-turn provide transport for a variety of client networks, e.g., IP and MPLS. This document uses procedures defined in the existing IETF specifications of Ethernet pseudowires carried over MPLS networks.
Many of the requirements for the services provided by the mechanisms explained in this document are also recognized by the MPLS transport profile (MPLS-TP) design effort formed jointly by the IETF and ITU-T [[[RFC5654]]]. For example, the ability to operate solely with network management control, the ability to use Operations, Administration, and Maintenance (OAM) that does not rely on IP forwarding, and the ability to provide light-weight proactive connection verification (CV) functionality.
The solution described in this document does not address all of the MPLS-TP requirements, but it provides a viable form of packet transport service using tools that are already available.
The key purpose of this document is to demonstrate that there is an existing IETF mechanism with known implementations that satisfies the requirements posed by the operator community. It is recognized that it is possible to design a more efficient method of satisfying the requirements, and the IETF anticipates that improved solutions will be proposed in the future as part of the MPLS-TP effort. Indeed, the solution described in this document is not intended to detract from the MPLS-TP effort. Instead, it provides legitimacy for that work by showing that there is a real demand from networks that are already deployed, and by indicating that the MPLS-TP solutions work is based on sound foundations.
Much of the notation used in this document is defined in [[[RFC3985]]] to which the reader is referred for definitions.
The architecture required for this mechanism is illustrated in Figure 1.
+----------------------------------------------------------------+ | | | IP/MPLS PSN (PHP may be enabled) | | (client) | | | | +---------------------------+ | | | | | | | MPLS PSN (No PHP) | | | | (server) | | | | | | | CE1 |PE1 PE2| CE2 | | +-----+ +-----+ +-----+ +-----+ | | | | | | | | | | | | | | | | | | | | | | | +------+ | | | | | | +------+ | | | | | | | | | 802.3| | | | | | | | 802.3| | | | | | +-----+ +-----+ +-----+ +-----+ | | | | | | | | | | | | | | +-- ---------------------- -+ | | | +----- --- -------- -- ---------------------- - -------- --- ----+ | | | |<--MPLS LSP (no PHP)->| | | | | | | | (server) | | | | | | | | | | | | |<------------PW----------->| | | | | | (server) | | | | | | | | |<-------------802.3 (Ethernet)-------------->| | | | (client) | | | | |<---------IP/MPLS LSP (PHP may be supported)-------->| | (client) |
Figure 1: Application Ethernet over MPLS PW to MPLS Transport
Networks
An 802.3 (Ethernet) circuit is established between CE1 and CE2. This circuit may be used for the concurrent transport of MPLS packets as well as IPv4 and IPv6 packets. The MPLS packets may carry IPv4, IPV6, or pseudowire payloads, and Penultimate Hop Popping (PHP) may be used. For clarity, these paths are labeled as the client in Figure 1.
An Ethernet pseudowire (PW) is provisioned between PE1 and PE2 and is used to carry the Ethernet from PE1 to PE2. The Ethernet PW is carried over an MPLS Packet Switched Network (PSN), but this PSN MUST NOT be configured with PHP. For clarity, this Ethernet PW and the MPLS PSN are labeled as the server in Figure 1. In the remainder of this document, call the server network a transport network.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [[[RFC2119]]].
PWE3 Configuration
The PWE3 encapsulation used by this specification to satisfy the transport requirement is Ethernet [[[RFC4448]]]. This is used in "raw" mode.
The Control Word MUST be used. The sequence number MUST be zero.
The use of the Pseudowire Setup and Maintenance Label Distribution Protocol [[[RFC4447]]] is not required by the profile of the PWE3 Ethernet pseudowire functionality defined in this document.
The pseudowire label is statically provisioned.
Operations, Administration, and Maintenance (OAM)
Within a connection, traffic units sent from the single source are constrained to stay within the connection under defect-free conditions. During misconnected defects, a connection can no longer be assumed to be constrained, and traffic units (and by implication also OAM packets) can 'leak' unidirectionally outside a connection. Therefore, during a misconnected state, it is not possible to rely on OAM, which relies on a request/response mechanism, and, for this reason, such OAM should be treated with caution if used for diagnostic purposes.
Further, when implementing an Equal Cost Multipath (ECMP) function with MPLS, use of the label stack as the path selector such that the OAM and data are not in a co-path SHOULD be avoided, as any failure in the data path will not be reflected in the OAM path. Therefore, an OAM that is carried within the data-path below the PW label (such as Virtual Circuit Connectivity Verification (VCCV)) is NOT vulnerable to the above failure mode. For these reasons, the OAM mechanism is as described in [[[RFC5085]]], which uses Bidirectional Forwarding Detection (BFD) [[[RFC5880]]] for connection verification (CV). The method of using BFD as a CV method in VCCV is described in [[[RFC5885]]]. One of the VCCV profiles described in Section 3.1 or Section 3.2 MUST be used. Once a VCCV control channel is provisioned and the operational status of the PW is UP, no other profile should be used until such time as the PW's operational status is set to DOWN.
VCCV Profile 1: BFD without IP/UDP Headers
When PE1 and PE2 are not IP capable or have not been configured with IP addresses, the following VCCV mechanism SHOULD be used.
The connection verification method used by VCCV is BFD with diagnostics as defined in [[[RFC5885]]].
[[[RFC5085]]] specifies that the first nibble is set to 0x1 to indicate a channel associated with a pseudowire [[[RFC4385]]].
The Version and the Reserved fields are set to zero, and the Channel Type is set to 0x7 to indicate that the payload carried is BFD without IP/UDP headers, as is defined in [[[RFC5885]]].
VCCV Profile 2: BFD with IP/UDP Headers
When PE1 and PE2 are IP capable and have been configured with IP addresses, the following VCCV mechanism may be used.
The connection verification method used by VCCV is BFD with diagnostics as defined in [[[RFC5885]]].
[[[RFC5085]]] specifies that the first nibble is set to 0x1 to indicate a channel associated with a pseudowire [[[RFC4385]]].
The Version and the Reserved fields are set to 0, and the Channel Type is set to 0x21 for IPv4 and 0x56 for IPv6 payloads [[[RFC4446]]].
MPLS Layer
The architecture of MPLS-enabled networks is described in [[[RFC3031]]]. This section describes a subset of the functionality of the MPLS- enabled PSN. There are two cases that need to be considered:
1. The case where external configuration is used.
2. The case where a control plane is available.
Where the use of a control plane is desired, this may be based on Generalized Multi-Protocol Label Switching (GMPLS) [[[RFC3945]]].
External Configuration
The use of external provisioning is not precluded from being supported by the current MPLS specifications. It is however explicitly described in this specification to address the
requirements specified by the ITU [[[RFC5654]]] to address the needs in a transport environment.
The MPLS encapsulation is specified in [[[RFC3032]]]. All MPLS labels used in the server layer (Figure 1) MUST be statically provisioned. Labels may be selected from either the per-platform or the per- interface label space.
All transport Label Switched Paths (LSPs) utilized by the PWs described in Section 2 MUST support both unidirectional and bidirectional point-to-point connections.
The transport LSPs SHOULD support unidirectional point-to-multipoint connections.
The forward and backward directions of a bidirectional connection SHOULD follow a symmetrically routed (reciprocal) LSP in the server network.
Equal Cost Multipath (ECMP) load balancing MUST NOT be configured on the transport LSPs utilized by the PWs described in Section 2.
The merging of Label Switched Paths is prohibited and MUST NOT be configured for the transport LSPs utilized by the PWs described in Section 2.
Penultimate hop popping by the transport Label Switched Routers (LSRs) MUST be disabled on transport LSPs.
Both EXP-Inferred-PSC LSPs (E-LSP) and Label-Only-Inferred-PSC LSPs (L-LSP) MUST be supported as defined in [[[RFC3270]]].
For the MPLS EXP field [[[RFC3270]]] [[[RFC5462]]], only the pipe and short- pipe models are supported.
Control Plane Configuration
In this section, we describe the control plane configuration when [[[RFC3209]]] or the bidirectional support in GMPLS ([[[RFC3471]]] and [[[RFC3473]]]) are used to configure the transport MPLS PSN. When these protocols are used to provide the control plane, the following are automatically provided:
1. There is no label merging unless it is deliberately enabled to
support Fast Re-route (FRR) [[[RFC3209]]].
2. A single path is provided end-to-end (there is no ECMP).
3. Label Switched Paths may be unidirectional or bidirectional as
required.
Additionally, the following configuration restrictions required to support external configuration MUST be applied:
o Penultimate hop popping [[[RFC3031]]] by the LSRs MUST be disabled on
LSPs providing PWE3 transport network functionality.
o Both E-LSP and L-LSP MUST be supported as defined in [[[RFC3270]]].
o The MPLS EXP [[[RFC5462]]] field is supported according to [[[RFC3270]]]
only when the pipe and short-pipe models are utilized.
Congestion Considerations
This document describes a method of using the existing PWE3 Ethernet pseudowire [[[RFC4448]]] to solve a particular network application. The congestion considerations associated with that pseudowire and all subsequent work on congestion considerations regarding Ethernet pseudowires are applicable to this RFC.
Security Considerations
This RFC provides a description of the use of existing IETF Proposed Standards to solve a network problem, and raises no new security issues.
The PWE3 security considerations are described in [[[RFC3985]]] and the Ethernet pseudowire security considerations of [[[RFC4448]]].
The Ethernet pseudowire is transported on an MPLS PSN; therefore, the security of the pseudowire itself will only be as good as the security of the MPLS PSN. The server MPLS PSN can be secured by various methods, as described in [[[RFC3031]]].
The use of static configuration exposes an MPLS PSN to a different set of security risks to those found in a PSN using dynamic routing. If a path is misconfigured in a statically configured network, the result can be a persistent black hole, or much worse, a persistent forwarding loop. On the other hand, most of the distributed components are less complex. This is however offset by the need to provide fail-over and redundancy in the management and configuration system and the communications paths between those central systems and the LSRs.
Security achieved by access control of media access control (MAC) addresses, and the security of the client layers, is out of the scope of this document.
Acknowledgements
The authors wish to thank Matthew Bocci, John Drake, Adrian Farrel, Andy Malis, and Yaakov Stein for their review and proposed enhancements to the text.
References
Normative References
[[[RFC2119]]] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[[[RFC3031]]] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
Label Switching Architecture", RFC 3031, January 2001.
[[[RFC3032]]] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack Encoding", RFC 3032, January 2001.
[[[RFC3209]]] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, December 2001.
[[[RFC3270]]] Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen,
P., Krishnan, R., Cheval, P., and J. Heinanen, "Multi- Protocol Label Switching (MPLS) Support of Differentiated Services", RFC 3270, May 2002.
[[[RFC3471]]] Berger, L., "Generalized Multi-Protocol Label Switching
(GMPLS) Signaling Functional Description", RFC 3471, January 2003.
[[[RFC3473]]] Berger, L., "Generalized Multi-Protocol Label Switching
(GMPLS) Signaling Resource ReserVation Protocol-Traffic Engineering (RSVP-TE) Extensions", RFC 3473, January 2003.
[[[RFC3945]]] Mannie, E., "Generalized Multi-Protocol Label Switching
(GMPLS) Architecture", RFC 3945, October 2004.
[[[RFC4385]]] Bryant, S., Swallow, G., Martini, L., and D. McPherson,
"Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for Use over an MPLS PSN", RFC 4385, February 2006.
[[[RFC4446]]] Martini, L., "IANA Allocations for Pseudowire Edge to Edge
Emulation (PWE3)", BCP 116, RFC 4446, April 2006.
[[[RFC4447]]] Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G.
Heron, "Pseudowire Setup and Maintenance Using the Label Distribution Protocol (LDP)", RFC 4447, April 2006.
[[[RFC4448]]] Martini, L., Rosen, E., El-Aawar, N., and G. Heron,
"Encapsulation Methods for Transport of Ethernet over MPLS Networks", RFC 4448, April 2006.
[[[RFC5085]]] Nadeau, T. and C. Pignataro, "Pseudowire Virtual Circuit
Connectivity Verification (VCCV): A Control Channel for Pseudowires", RFC 5085, December 2007.
[[[RFC5462]]] Andersson, L. and R. Asati, "Multiprotocol Label Switching
(MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic Class" Field", RFC 5462, February 2009.
[[[RFC5880]]] Katz, D. and D. Ward, "Bidirectional Forwarding Detection
(BFD)", RFC 5880, June 2010.
[[[RFC5885]]] Nadeau, T. and C. Pignataro, "Bidirectional Forwarding
Detection (BFD) for the Pseudowire Virtual Circuit Connectivity Verification (VCCV)", RFC 5885, June 2010.
Informative References
[[[RFC3985]]] Bryant, S. and P. Pate, "Pseudo Wire Emulation Edge-to-
Edge (PWE3) Architecture", RFC 3985, March 2005.
[[[RFC5654]]] Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N.,
and S. Ueno, "Requirements of an MPLS Transport Profile", RFC 5654, September 2009.
Authors' Addresses
Stewart Bryant (editor) Cisco Systems 250, Longwater, Green Park Reading RG2 6GB UK
EMail: [email protected]
Monique Morrow Cisco Systems Glatt-com CH-8301 Glattzentrum Switzerland
EMail: [email protected]
George Swallow Cisco Systems 1414 Massachusetts Ave. Boxborough, MA 01719
EMail: [email protected]
Rao Cherukuri Juniper Networks 1194 N. Mathilda Ave. Sunnyvale, CA 94089
EMail: [email protected]
Thomas D. Nadeau Huawei Technologies Central Expressway Santa Clara, CA 95050
EMail: [email protected]
Neil Harrison BT
EMail: [email protected]
Ben Niven-Jenkins Velocix 326 Science Park Milton Road, Cambridge CB4 0WG UK
EMail: [email protected]