RFC381
Network Working Group J. McQuillan
Request for Comments: 381 D. Walden
NIC: 11151 Bolt Beranek and Newman Inc.
26 July 1972
Three Aids To Improved Network Operation
Scheduled Software Maintenance
As the ARPA Network has grown larger, we have found it difficult to find times when necessary new software can be slipped into the network without disrupting anyone. For instance, there is always intrasite traffic between the machines at MIT, and there is almost always traffic between the AMES TIP and IMP--the sun never sets on the ARPA Network. To minimize unscheduled disruptions and to simultaneously let us do what we have to do, we propose to schedule 7 A.M. - 8 A.M. eastern time every Tuesday as a time when the IMPs can be reloaded. We will probably not use this period every Tuesday, but we do reserve this period every Tuesday. The above period is in addition to the several hours a month already scheduled at each site for hardware preventative maintenance.
Because a network user may not know when his machine is scheduled for maintenance or because he may forget and work through the Tuesday morning software period, we propose to generalize the IMP-Going-Down IMP-to-Host control message so it may be used to remind the user. This message (described in detail below) will contain information that the IMP is going down in m times five minutes, for n times 5 minutes, for a given reason. Hosts (and the TIP) should use this information to remind all their Network users that the IMP will be going down after the stated interval.
Occasionally there is an emergency reason for restarting or reloading an IMP. For instance, while three Hosts at a site are functioning well, one Host cannot communicate with the IMP. This sort of situation sometimes requires the IMP to be restarted. Such a restart will be preceded by several minutes by an IMP-Going-Down Message to allow working users to save their work in such a way that they can restart once the IMP is back up.
In both of these cases, as well as cases where an IMP is performing so poorly that is must be shut down quickly, a type 2 IMP-to-HOST message will be transmitted to the HOST about 30 seconds before the IMP goes down. Finally, of course, there may be occasions when the IMP crashes so quickly that no warning is given, but the IMP will never be intentionally shut down in this way.
IMP-to-Host Communication
There have long been complaints that the IMP-to-Host error messages were not precise enough or were just plain ambiguous. In RFC #312 we proposed some additional error messages. These and other IMP-to-Host message changes will be made on August 14, 1972 and we encourage Hosts to modify their NCP's as appropriate by then. Unmodified NCPs will probably continue to work after this change, but each site should look into this question carefully. The table below lists all the IMP-to-Host messages and clearly indicates the changes which will be made.
Type Old Meaning New Meaning
0 Regular Messages Same
1 Error without Error in Leader of Host-to-
identification IMP Message
Bits 31,32=00 - IMP's
error flip-flop set on
the first 32 bits of a
Host-to-IMP message which
the IMP therefore cannot
identify
Bits 31,32=01 - Host-to-IMP
message too short (less
than 32 bits)
Bits 31,32=10 - illegal
Host-to-IMP code
2 IMP Going Down IMP Going Down
Bits 17-32 coded as follows:
All bits zero - going down in
30 sec.
Bits 17,18=01 - scheduled
hardware PM
Bits 17,18=10 - scheduled
software reload
Bits 17,18=11 - emergency
reload or restart
Bits 19-22 - how soon the
IMP is going down - in
5 minute units
Bits 23-32 - how long the IMP
will be down - in 5
minute units
3 Blocked Link Unassigned
4 NOF Same
5 RFNM Same
6 Link Table Full Unassigned
7 Destination Dead Destination Dead
Bit 32=0 - the destination
IMP is dead, or cannot be
reached, or does not exist
Bit 32=1 - the destination
Host is dead or does not
exist
8 Error with identi- Error in Data of Host-to IMP
fication Message
IMP's error flip-flop set
on the data bits of a Host-
to-IMP message identified
by the given source and link
9 Incomplete Transmission Incomplete Transmission
Bits 31,32=00 - the destination
Host did not take the message
for a long time
Bits 31,32=01 - Host-to-IMP
message too long (more
than 8095 bits)
Bits 31,32=10 - Host-to IMP
message too slow. The
last message took more
than 15 secs. between
the first bit and the
last bit, and was discarded
Bits 31,32=11 - Host-to-
IMP message lost in the
subnet
10 Unassigned IMP-Host Interface Reset
The IMP's ready line has
been dropped and pending
output to the Host discarded
(probably because the Host
has not taken messages from
the IMP for a long time).
The IMP will return a type 1
message of subtype 0 at the
completion of the next Host-
to-IMP message.
These changes can be summarized as follows:
1. There is now one and only one IMP-to-Host message in response to
each Host-to-IMP regular message.
2. Message types 1, 2, 7 and 9 now carry additional information.
3. Message type 10 has been added.
4. Message types 3 and 6 have been discarded.
Network News Service
We have instituted a Network news service. TIP users get the news by typing the TIP command @NEWS. Users of other Host can get the news by ICPing to socket 15600031 (octal) at the BBN Tenex.
If you have further suggestions for improving the operation of the Network, we request your comments.
[ This RFC was put into machine readable form for entry ]
[ into the online RFC archives by Lorrie Shiota 08/00]
