RFC5060
Network Working Group R. Sivaramu Request for Comments: 5060 Cisco Systems Category: Standards Track J. Lingard
Arastra, Inc
D. McWalter
Data Connection Ltd
B. Joshi
Infosys Technologies Ltd
A. Kessler
Cisco Systems
January 2008
Protocol Independent Multicast MIB
Status of This Memo
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
Abstract
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects used for managing the Protocol Independent Multicast (PIM) protocols: PIM-SM (Sparse Mode), BIDIR-PIM (Bidirectional), and PIM-DM (Dense Mode). This document is part of work in progress to obsolete RFC 2934, and is to be preferred where the two documents overlap. This document does not obsolete RFC 2934.
Contents
Introduction
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects used for managing the Protocol Independent Multicast (PIM) protocols (PIM-SM RFC4601, BIDIR-PIM RFC5015, and PIM-DM RFC3973).
This document is part of work in progress to obsolete RFC 2934 RFC2934. RFC 2934 defined an experimental MIB module for managing the PIM protocols. The MIB module defined by this document is a re- working of the MIB module from RFC 2934, with major changes that include the following.
o This MIB module is independent of IP version, whereas RFC 2934
only supported IPv4.
o This MIB module includes support for managing BIDIR-PIM.
o This MIB module retains limited support for managing PIM-DM
RFC3973, but that is no longer its primary purpose.
o This MIB module does not include support for managing PIM-SM v1.
o This MIB module does not depend on the IPv4 Multicast Routing MIB
defined in RFC 2932 RFC2932.
o This MIB module includes support for configuring static Rendezvous
Points (RPs).
o This MIB module includes support for configuring anycast RPs
RFC4610.
Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 RFC2119.
The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 RFC3410.
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 RFC2578, STD 58, RFC 2579 RFC2579 and STD 58, RFC 2580 RFC2580.
Overview
This MIB module contains the following tables.
1. The PIM Interface Table, which contains one row per IP version
for each interface of the router which is running PIM.
2. The PIM Neighbor Table, which contains one row for each of the
router's PIM neighbors.
3. The PIM Neighbor Secondary Address Table, which contains one row
for each secondary address advertised by each of the router's
PIM neighbors.
4. The PIM (*,G) State Table, which contains one row for each group
for which PIM has (*,G) state.
5. The PIM (*,G,I) State Table, which contains one row for each
group and interface for which PIM has interface-specific (*,G)
state.
6. The PIM (S,G) State Table, which contains one row for each
source and group for which PIM has (S,G) state.
7. The PIM (S,G,I) State Table, which contains one row for each
source, group, and interface for which PIM has interface-
specific (S,G) state.
8. The PIM (S,G,rpt) State Table, which contains one row for each
source and group for which PIM has (S,G,rpt) state.
9. The PIM (S,G,rpt,I) State Table, which contains one row for each
source, group, and interface for which PIM has interface-
specific (S,G,rpt) state.
10. The PIM Bidir DF-Election Table, which contains one row per
interface for each Rendezvous Point (RP) for which
Bidirectional-PIM Designated Forwarder (DF) election state is
maintained.
11. The PIM Static RP Table, which contains one row per range of
multicast group addresses for which a particular configured RP
should be used.
12. The PIM Group Mapping Table, which contains one row for each
mapping from a multicast group address prefix to the PIM mode
and RP address to use for groups within that group prefix,
regardless of the source of the group mapping information.
13. The PIM Anycast-RP Set Table, which contains one row for each RP
within each Anycast-RP set of which the local router is a
member.
This MIB module uses textual conventions defined in the IF-MIB RFC2863, the INET-ADDRESS-MIB RFC4001, and the IANA-RTPROTO-MIB [RTPROTO]. This MIB module REFERENCEs RFC3376, RFC3569, RFC3618, RFC3810, RFC3956, RFC3973, RFC4601, RFC4610, RFC5015, RFC5059, and [IPMCAST-MIB].
Definitions
PIM-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, mib-2, NOTIFICATION-TYPE, Unsigned32, Counter32, Counter64, Gauge32, TimeTicks FROM SNMPv2-SMI -- RFC2578 TEXTUAL-CONVENTION, RowStatus, TruthValue, StorageType FROM SNMPv2-TC -- RFC2579 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC2580 InterfaceIndexOrZero, InterfaceIndex FROM IF-MIB -- RFC2863 InetAddressType, InetAddressPrefixLength, InetAddress, InetVersion FROM INET-ADDRESS-MIB -- RFC4001 IANAipRouteProtocol FROM IANA-RTPROTO-MIB; -- [RTPROTO]
pimStdMIB MODULE-IDENTITY
LAST-UPDATED "200711020000Z" -- 2 November 2007
ORGANIZATION
"IETF Protocol Independent Multicast (PIM) Working Group"
CONTACT-INFO
"Email: [email protected]
WG charter:
http://www.ietf.org/html.charters/pim-charter.html" DESCRIPTION "The MIB module for management of PIM routers.
Copyright (C) The IETF Trust (2007). This version of this
MIB module is part of RFC 5060; see the RFC itself for full
legal notices."
REVISION "200711020000Z" -- 2 November 2007
DESCRIPTION "Initial version, published as RFC 5060."
::= { mib-2 157 }
-- -- Textual Conventions --
PimMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The PIM mode in which a group is operating.
none(1) The group is not using PIM, which may be the
case if, for example, it is a link-local or
unroutable group address.
ssm(2) Source-Specific Multicast (SSM) with PIM Sparse
Mode.
asm(3) Any Source Multicast (ASM) with PIM Sparse
Mode.
bidir(4) Bidirectional PIM.
dm(5) PIM Dense Mode.
other(6) Any other PIM mode."
SYNTAX INTEGER {
none(1),
ssm(2),
asm(3),
bidir(4),
dm(5),
other(6)
}
PimGroupMappingOriginType ::= TEXTUAL-CONVENTION
STATUS current DESCRIPTION
"The mechanism by which a PIM group mapping was learned.
fixed(1) Link-local or unroutable group mappings.
configRp(2) Local static RP configuration.
configSsm(3) Local SSM Group configuration.
bsr(4) The PIM Bootstrap Router (BSR) mechanism.
autoRP(5) Cisco's Auto-RP mechanism.
embedded(6) The Embedded-RP mechanism where the RP address
is embedded in the multicast group address.
other(7) Any other mechanism."
REFERENCE "RFC 3569, RFC 3956, and RFC 5059" SYNTAX INTEGER { fixed(1), configRp(2), configSsm(3), bsr(4), autoRP(5), embedded(6), other(7) }
-- -- Top-level structure --
pimNotifications OBJECT IDENTIFIER ::= { pimStdMIB 0 } pim OBJECT IDENTIFIER ::= { pimStdMIB 1 }
pimKeepalivePeriod OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The duration of the Keepalive Timer. This is the period
during which the PIM router will maintain (S,G) state in the
absence of explicit (S,G) local membership or (S,G) join
messages received to maintain it. This timer period is
called the Keepalive_Period in the PIM-SM specification. It
is called the SourceLifetime in the PIM-DM specification.
The storage type of this object is determined by
pimDeviceConfigStorageType."
REFERENCE "RFC 4601 section 4.11"
DEFVAL { 210 }
::= { pim 14 }
pimRegisterSuppressionTime OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The duration of the Register Suppression Timer. This is
the period during which a PIM Designated Router (DR) stops
sending Register-encapsulated data to the Rendezvous Point
(RP) after receiving a Register-Stop message. This object
is used to run timers both at the DR and at the RP. This
timer period is called the Register_Suppression_Time in the
PIM-SM specification.
The storage type of this object is determined by
pimDeviceConfigStorageType."
REFERENCE "RFC 4601 section 4.11"
DEFVAL { 60 }
::= { pim 15 }
pimStarGEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of entries in the pimStarGTable."
::= { pim 16 }
pimStarGIEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of entries in the pimStarGITable."
::= { pim 17 }
pimSGEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of entries in the pimSGTable."
::= { pim 18 }
pimSGIEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of entries in the pimSGITable."
::= { pim 19 }
pimSGRptEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of entries in the pimSGRptTable."
::= { pim 20 }
pimSGRptIEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of entries in the pimSGRptITable."
::= { pim 21 }
pimOutAsserts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Asserts sent by this router.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, for example,
when the device is rebooted."
REFERENCE "RFC 4601 section 4.6"
::= { pim 22 }
pimInAsserts OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Asserts received by this router. Asserts
are multicast to all routers on a network. This counter is
incremented by all routers that receive an assert, not only
those routers that are contesting the assert.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, for example,
when the device is rebooted."
REFERENCE "RFC 4601 section 4.6"
::= { pim 23 }
pimLastAssertInterface OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The interface on which this router most recently sent or
received an assert, or zero if this router has not sent or
received an assert."
REFERENCE "RFC 4601 section 4.6"
::= { pim 24 }
pimLastAssertGroupAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of the multicast group address in the most
recently sent or received assert. If this router has not
sent or received an assert, then this object is set to
unknown(0)."
::= { pim 25 }
pimLastAssertGroupAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The multicast group address in the most recently sent or
received assert. The InetAddressType is given by the
pimLastAssertGroupAddressType object."
::= { pim 26 }
pimLastAssertSourceAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of the source address in the most recently
sent or received assert. If the most recent assert was
(*,G), or if this router has not sent or received an assert,
then this object is set to unknown(0)."
::= { pim 27 }
pimLastAssertSourceAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The source address in the most recently sent or received
assert. The InetAddressType is given by the
pimLastAssertSourceAddressType object."
::= { pim 28 }
pimNeighborLossNotificationPeriod OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum time that must elapse between pimNeighborLoss
notifications originated by this router. The maximum value
65535 represents an 'infinite' time, in which case, no
pimNeighborLoss notifications are ever sent.
The storage type of this object is determined by
pimDeviceConfigStorageType."
DEFVAL { 0 }
::= { pim 29 }
pimNeighborLossCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of neighbor loss events that have occurred.
This counter is incremented when the neighbor timer expires,
and the router has no other neighbors on the same interface
with the same IP version and a lower IP address than itself.
This counter is incremented whenever a pimNeighborLoss
notification would be generated.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, for example,
when the device is rebooted."
REFERENCE "RFC 4601 section 4.3.2"
::= { pim 30 }
pimInvalidRegisterNotificationPeriod OBJECT-TYPE
SYNTAX Unsigned32 (10..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum time that must elapse between
pimInvalidRegister notifications originated by this router.
The default value of 65535 represents an 'infinite' time, in
which case, no pimInvalidRegister notifications are ever
sent.
The non-zero minimum allowed value provides resilience
against propagation of denial-of-service attacks from the
data and control planes to the network management plane.
The storage type of this object is determined by
pimDeviceConfigStorageType."
DEFVAL { 65535 }
::= { pim 31 }
pimInvalidRegisterMsgsRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of invalid PIM Register messages that have been
received by this device.
A PIM Register message is invalid if either
o the destination address of the Register message does not
match the Group to RP mapping on this device, or
o this device believes the group address to be within an
SSM address range, but this Register implies ASM usage.
These conditions can occur transiently while RP mapping
changes propagate through the network. If this counter is
incremented repeatedly over several minutes, then there is a
persisting configuration error that requires correction.
The active Group to RP mapping on this device is specified
by the object pimGroupMappingPimMode. If there is no such
mapping, then the object pimGroupMappingPimMode is absent.
The RP address contained in the invalid Register is
pimInvalidRegisterRp.
Multicast data carried by invalid Register messages is
discarded. The discarded data is from a source directly
connected to pimInvalidRegisterOrigin, and is addressed to
pimInvalidRegisterGroup.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, for example,
when the device is rebooted."
REFERENCE "RFC 4601 section 4.4.2, RFC 3569, and
'IP Multicast MIB' (August 2007) ipMcastSsmRangeTable"
::= { pim 32 }
pimInvalidRegisterAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type stored in pimInvalidRegisterOrigin,
pimInvalidRegisterGroup, and pimInvalidRegisterRp.
If no invalid Register messages have been received, then
this object is set to unknown(0)."
::= { pim 33 }
pimInvalidRegisterOrigin OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The source address of the last invalid Register message
received by this device."
::= { pim 34 }
pimInvalidRegisterGroup OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP multicast group address to which the last invalid
Register message received by this device was addressed."
::= { pim 35 }
pimInvalidRegisterRp OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The RP address to which the last invalid Register message
received by this device was delivered."
::= { pim 36 }
pimInvalidJoinPruneNotificationPeriod OBJECT-TYPE
SYNTAX Unsigned32 (10..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum time that must elapse between
pimInvalidJoinPrune notifications originated by this router.
The default value of 65535 represents an 'infinite' time, in
which case, no pimInvalidJoinPrune notifications are ever
sent.
The non-zero minimum allowed value provides resilience
against propagation of denial-of-service attacks from the
control plane to the network management plane.
The storage type of this object is determined by
pimDeviceConfigStorageType."
DEFVAL { 65535 }
::= { pim 37 }
pimInvalidJoinPruneMsgsRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of invalid PIM Join/Prune messages that have
been received by this device.
A PIM Join/Prune message is invalid if either
o the Group to RP mapping specified by this message does not
match the Group to RP mapping on this device, or
o this device believes the group address to be within an
SSM address range, but this Join/Prune (*,G) or (S,G,rpt)
implies ASM usage.
These conditions can occur transiently while RP mapping
changes propagate through the network. If this counter is
incremented repeatedly over several minutes, then there is a
persisting configuration error that requires correction.
The active Group to RP mapping on this device is specified
by the object pimGroupMappingPimMode. If there is no such
mapping, then the object pimGroupMappingPimMode is absent.
The RP address contained in the invalid Join/Prune is
pimInvalidJoinPruneRp.
Invalid Join/Prune messages are discarded. This may result
in loss of multicast data affecting listeners downstream of
pimInvalidJoinPruneOrigin, for multicast data addressed to
pimInvalidJoinPruneGroup.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, for example,
when the device is rebooted."
REFERENCE "RFC 4601 section 4.5.2, RFC 3569, and
'IP Multicast MIB' (August 2007) ipMcastSsmRangeTable"
::= { pim 38 }
pimInvalidJoinPruneAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type stored in pimInvalidJoinPruneOrigin,
pimInvalidJoinPruneGroup, and pimInvalidJoinPruneRp.
If no invalid Join/Prune messages have been received, this
object is set to unknown(0)."
::= { pim 39 }
pimInvalidJoinPruneOrigin OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The source address of the last invalid Join/Prune message
received by this device."
::= { pim 40 }
pimInvalidJoinPruneGroup OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP multicast group address carried in the last
invalid Join/Prune message received by this device."
::= { pim 41 }
pimInvalidJoinPruneRp OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The RP address carried in the last invalid Join/Prune
message received by this device."
::= { pim 42 }
pimRPMappingNotificationPeriod OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The minimum time that must elapse between
pimRPMappingChange notifications originated by this router.
The default value of 65535 represents an 'infinite' time, in
which case, no pimRPMappingChange notifications are ever
sent.
The storage type of this object is determined by
pimDeviceConfigStorageType."
DEFVAL { 65535 }
::= { pim 43 }
pimRPMappingChangeCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of changes to active RP mappings on this device.
Information about active RP mappings is available in
pimGroupMappingTable. Only changes to active mappings cause
this counter to be incremented. That is, changes that
modify the pimGroupMappingEntry with the highest precedence
for a group (lowest value of pimGroupMappingPrecedence).
Such changes may result from manual configuration of this
device, or from automatic RP mapping discovery methods
including the PIM Bootstrap Router (BSR) mechanism.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, for example,
when the device is rebooted."
REFERENCE "RFC 5059"
::= { pim 44 }
pimInterfaceElectionNotificationPeriod OBJECT-TYPE
SYNTAX Unsigned32 (0..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current
DESCRIPTION
"The minimum time that must elapse between
pimInterfaceElection notifications originated by this
router. The default value of 65535 represents an 'infinite'
time, in which case, no pimInterfaceElection notifications
are ever sent.
The storage type of this object is determined by
pimDeviceConfigStorageType."
DEFVAL { 65535 }
::= { pim 45 }
pimInterfaceElectionWinCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this device has been elected DR or DF
on any interface.
Elections occur frequently on newly-active interfaces, as
triggered Hellos establish adjacencies. This counter is not
incremented for elections on an interface until the first
periodic Hello has been sent. If this router is the DR or
DF at the time of sending the first periodic Hello after
interface activation, then this counter is incremented
(once) at that time.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, for example,
when the device is rebooted."
REFERENCE "RFC 4601 section 4.3.2 and RFC 5015 section 3.5.2"
::= { pim 46 }
pimRefreshInterval OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The interval between successive State Refresh messages sent
by an Originator. This timer period is called the
RefreshInterval in the PIM-DM specification. This object is
used only by PIM-DM.
The storage type of this object is determined by
pimDeviceConfigStorageType."
REFERENCE "RFC 3973 section 4.8"
DEFVAL { 60 }
::= { pim 47 }
pimDeviceConfigStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The storage type used for the global PIM configuration of
this device, comprised of the objects listed below. If this
storage type takes the value 'permanent', write-access to
the listed objects need not be allowed.
The objects described by this storage type are:
pimKeepalivePeriod, pimRegisterSuppressionTime,
pimNeighborLossNotificationPeriod,
pimInvalidRegisterNotificationPeriod,
pimInvalidJoinPruneNotificationPeriod,
pimRPMappingNotificationPeriod,
pimInterfaceElectionNotificationPeriod, and
pimRefreshInterval."
DEFVAL { nonVolatile }
::= { pim 48 }
-- -- The PIM Interface Table --
pimInterfaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the router's PIM interfaces.
PIM is enabled on all interfaces listed in this table."
::= { pim 1 }
pimInterfaceEntry OBJECT-TYPE
SYNTAX PimInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimInterfaceTable. This
entry is preserved on agent restart."
INDEX { pimInterfaceIfIndex,
pimInterfaceIPVersion }
::= { pimInterfaceTable 1 }
PimInterfaceEntry ::= SEQUENCE {
pimInterfaceIfIndex InterfaceIndex, pimInterfaceIPVersion InetVersion, pimInterfaceAddressType InetAddressType, pimInterfaceAddress InetAddress, pimInterfaceGenerationIDValue Unsigned32, pimInterfaceDR InetAddress, pimInterfaceDRPriority Unsigned32, pimInterfaceDRPriorityEnabled TruthValue, pimInterfaceHelloInterval Unsigned32, pimInterfaceTrigHelloInterval Unsigned32, pimInterfaceHelloHoldtime Unsigned32, pimInterfaceJoinPruneInterval Unsigned32, pimInterfaceJoinPruneHoldtime Unsigned32, pimInterfaceDFElectionRobustness Unsigned32, pimInterfaceLanDelayEnabled TruthValue, pimInterfacePropagationDelay Unsigned32, pimInterfaceOverrideInterval Unsigned32, pimInterfaceEffectPropagDelay Unsigned32, pimInterfaceEffectOverrideIvl Unsigned32, pimInterfaceSuppressionEnabled TruthValue, pimInterfaceBidirCapable TruthValue, pimInterfaceDomainBorder TruthValue, pimInterfaceStubInterface TruthValue, pimInterfacePruneLimitInterval Unsigned32, pimInterfaceGraftRetryInterval Unsigned32, pimInterfaceSRPriorityEnabled TruthValue, pimInterfaceStatus RowStatus, pimInterfaceStorageType StorageType
}
pimInterfaceIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex value of this PIM interface."
::= { pimInterfaceEntry 1 }
pimInterfaceIPVersion OBJECT-TYPE
SYNTAX InetVersion
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP version of this PIM interface. A physical interface
may be configured in multiple modes concurrently, e.g., IPv4
and IPv6; however, the traffic is considered to be logically
separate."
::= { pimInterfaceEntry 2 }
pimInterfaceAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of this PIM interface."
::= { pimInterfaceEntry 3 }
pimInterfaceAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary IP address of this router on this PIM
interface. The InetAddressType is given by the
pimInterfaceAddressType object."
REFERENCE "RFC 4601 sections 4.1.6, 4.3.1-4.3.4, and 4.5.1"
::= { pimInterfaceEntry 4 }
pimInterfaceGenerationIDValue OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the Generation ID this router inserted in the
last PIM Hello message it sent on this interface."
REFERENCE "RFC 4601 section 4.3.1"
::= { pimInterfaceEntry 5 }
pimInterfaceDR OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary IP address of the Designated Router on this PIM
interface. The InetAddressType is given by the
pimInterfaceAddressType object."
REFERENCE "RFC 4601 section 4.3"
::= { pimInterfaceEntry 6 }
pimInterfaceDRPriority OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Designated Router Priority value inserted into the DR
Priority option in PIM Hello messages transmitted on this
interface. Numerically higher values for this object
indicate higher priorities."
REFERENCE "RFC 4601 section 4.3.2"
DEFVAL { 1 }
::= { pimInterfaceEntry 7 }
pimInterfaceDRPriorityEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Evaluates to TRUE if all routers on this interface are
using the DR Priority option."
REFERENCE "RFC 4601 section 4.3.2"
::= { pimInterfaceEntry 8 }
pimInterfaceHelloInterval OBJECT-TYPE
SYNTAX Unsigned32 (0..18000)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The frequency at which PIM Hello messages are transmitted
on this interface. This object corresponds to the
'Hello_Period' timer value defined in the PIM-SM
specification. A value of zero represents an 'infinite'
interval, and indicates that periodic PIM Hello messages
should not be sent on this interface."
REFERENCE "RFC 4601 section 9"
DEFVAL { 30 }
::= { pimInterfaceEntry 9 }
pimInterfaceTrigHelloInterval OBJECT-TYPE
SYNTAX Unsigned32 (0..60)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum time before this router sends a triggered PIM
Hello message on this interface. This object corresponds to
the 'Trigered_Hello_Delay' timer value defined in the PIM-SM
specification. A value of zero has no special meaning and
indicates that triggered PIM Hello messages should always be
sent immediately."
REFERENCE "RFC 4601 section 4.11"
DEFVAL { 5 }
::= { pimInterfaceEntry 10 }
pimInterfaceHelloHoldtime OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value set in the Holdtime field of PIM Hello messages
transmitted on this interface. A value of 65535 represents
an 'infinite' holdtime. Implementations are recommended
to use a holdtime that is 3.5 times the value of
pimInterfaceHelloInterval, or 65535 if
pimInterfaceHelloInterval is set to zero."
REFERENCE "RFC 4601 sections 4.3.2 and 4.9.2"
DEFVAL { 105 }
::= { pimInterfaceEntry 11 }
pimInterfaceJoinPruneInterval OBJECT-TYPE
SYNTAX Unsigned32 (0..18000)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The frequency at which this router sends PIM Join/Prune
messages on this PIM interface. This object corresponds to
the 't_periodic' timer value defined in the PIM-SM
specification. A value of zero represents an 'infinite'
interval, and indicates that periodic PIM Join/Prune
messages should not be sent on this interface."
REFERENCE "RFC 4601 section 4.11"
DEFVAL { 60 }
::= { pimInterfaceEntry 12 }
pimInterfaceJoinPruneHoldtime OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value inserted into the Holdtime field of a PIM
Join/Prune message sent on this interface. A value of 65535
represents an 'infinite' holdtime. Implementations are
recommended to use a holdtime that is 3.5 times the value of
pimInterfaceJoinPruneInterval, or 65535 if
pimInterfaceJoinPruneInterval is set to zero. PIM-DM
implementations are recommended to use the value of
pimInterfacePruneLimitInterval."
REFERENCE "RFC 4601 sections 4.5.3 and 4.9.5"
DEFVAL { 210 }
::= { pimInterfaceEntry 13 }
pimInterfaceDFElectionRobustness OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum number of PIM DF-Election messages that must be
lost in order for DF election on this interface to fail."
DEFVAL { 3 }
::= { pimInterfaceEntry 14 }
pimInterfaceLanDelayEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Evaluates to TRUE if all routers on this interface are
using the LAN Prune Delay option."
REFERENCE "RFC 4601 sections 4.3.3 and 4.9.2"
::= { pimInterfaceEntry 15 }
pimInterfacePropagationDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..32767)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The expected propagation delay between PIM routers on this
network or link.
This router inserts this value into the Propagation_Delay
field of the LAN Prune Delay option in the PIM Hello
messages sent on this interface. Implementations SHOULD
enforce a lower bound on the permitted values for this
object to allow for scheduling and processing delays within
the local router."
DEFVAL { 500 }
::= { pimInterfaceEntry 16 }
pimInterfaceOverrideInterval OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value this router inserts into the Override_Interval
field of the LAN Prune Delay option in the PIM Hello
messages it sends on this interface.
When overriding a prune, PIM routers pick a random timer
duration up to the value of this object. The more PIM
routers that are active on a network, the more likely it is
that the prune will be overridden after a small proportion
of this time has elapsed.
The more PIM routers are active on this network, the larger
this object should be to obtain an optimal spread of prune
override latencies."
REFERENCE "RFC 4601 section 4.3.3"
DEFVAL { 2500 }
::= { pimInterfaceEntry 17 }
pimInterfaceEffectPropagDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..32767)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Effective Propagation Delay on this interface. This
object is always 500 if pimInterfaceLanDelayEnabled is
FALSE."
REFERENCE "RFC 4601 section 4.3.3"
::= { pimInterfaceEntry 18 }
pimInterfaceEffectOverrideIvl OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Effective Override Interval on this interface. This
object is always 2500 if pimInterfaceLanDelayEnabled is
FALSE."
REFERENCE "RFC 4601 section 4.3.3"
::= { pimInterfaceEntry 19 }
pimInterfaceSuppressionEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether join suppression is enabled on this interface.
This object is always TRUE if pimInterfaceLanDelayEnabled is
FALSE."
REFERENCE "RFC 4601 section 4.3.3"
::= { pimInterfaceEntry 20 }
pimInterfaceBidirCapable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Evaluates to TRUE if all routers on this interface are
using the Bidirectional-PIM Capable option."
REFERENCE "RFC 5015 section 3.2 and 3.7.4"
::= { pimInterfaceEntry 21 }
pimInterfaceDomainBorder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Whether or not this interface is a PIM domain border. This
includes acting as a border for PIM Bootstrap Router (BSR)
messages, if the BSR mechanism is in use."
DEFVAL { false }
::= { pimInterfaceEntry 22 }
pimInterfaceStubInterface OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Whether this interface is a 'stub interface'. If this
object is set to TRUE, then no PIM packets are sent out this
interface, and any received PIM packets are ignored.
Setting this object to TRUE is a security measure for
interfaces towards untrusted hosts. This allows an
interface to be configured for use with IGMP (Internet Group
Management Protocol) or MLD (Multicast Listener Discovery)
only, which protects the PIM router from forged PIM messages
on the interface.
To communicate with other PIM routers using this interface,
this object must remain set to FALSE.
Changing the value of this object while the interface is
operational causes PIM to be disabled and then re-enabled on
this interface."
REFERENCE "RFC 3376, RFC 3810"
DEFVAL { false }
::= { pimInterfaceEntry 23 }
pimInterfacePruneLimitInterval OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum interval that must transpire between two
successive Prunes sent by a router. This object corresponds
to the 't_limit' timer value defined in the PIM-DM
specification. This object is used only by PIM-DM."
REFERENCE "RFC 3973 section 4.8"
DEFVAL { 60 }
::= { pimInterfaceEntry 24 }
pimInterfaceGraftRetryInterval OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum interval that must transpire between two
successive Grafts sent by a router. This object corresponds
to the 'Graft_Retry_Period' timer value defined in the
PIM-DM specification. This object is used only by PIM-DM."
REFERENCE "RFC 3973 section 4.8"
DEFVAL { 3 }
::= { pimInterfaceEntry 25 }
pimInterfaceSRPriorityEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Evaluates to TRUE if all routers on this interface are
using the State Refresh option. This object is used only by
PIM-DM."
::= { pimInterfaceEntry 26 }
pimInterfaceStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this entry. Creating the entry enables PIM
on the interface; destroying the entry disables PIM on the
interface.
This status object can be set to active(1) without setting
any other columnar objects in this entry.
All writeable objects in this entry can be modified when the
status of this entry is active(1)."
::= { pimInterfaceEntry 27 }
pimInterfaceStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this row. Rows having the value
'permanent' need not allow write-access to any columnar
objects in the row."
DEFVAL { nonVolatile }
::= { pimInterfaceEntry 28 }
-- -- The PIM Neighbor Table --
pimNeighborTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the router's PIM neighbors."
::= { pim 2 }
pimNeighborEntry OBJECT-TYPE
SYNTAX PimNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimNeighborTable."
INDEX { pimNeighborIfIndex,
pimNeighborAddressType,
pimNeighborAddress }
::= { pimNeighborTable 1 }
PimNeighborEntry ::= SEQUENCE {
pimNeighborIfIndex InterfaceIndex, pimNeighborAddressType InetAddressType, pimNeighborAddress InetAddress, pimNeighborGenerationIDPresent TruthValue, pimNeighborGenerationIDValue Unsigned32, pimNeighborUpTime TimeTicks, pimNeighborExpiryTime TimeTicks,
pimNeighborDRPriorityPresent TruthValue, pimNeighborDRPriority Unsigned32, pimNeighborLanPruneDelayPresent TruthValue, pimNeighborTBit TruthValue, pimNeighborPropagationDelay Unsigned32, pimNeighborOverrideInterval Unsigned32, pimNeighborBidirCapable TruthValue, pimNeighborSRCapable TruthValue
}
pimNeighborIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of ifIndex for the interface used to reach this
PIM neighbor."
::= { pimNeighborEntry 1 }
pimNeighborAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of this PIM neighbor."
::= { pimNeighborEntry 2 }
pimNeighborAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The primary IP address of this PIM neighbor. The
InetAddressType is given by the pimNeighborAddressType
object."
::= { pimNeighborEntry 3 }
pimNeighborGenerationIDPresent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Evaluates to TRUE if this neighbor is using the Generation
ID option."
REFERENCE "RFC 4601 section 4.3.1"
::= { pimNeighborEntry 4 }
pimNeighborGenerationIDValue OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the Generation ID from the last PIM Hello
message received from this neighbor. This object is always
zero if pimNeighborGenerationIDPresent is FALSE."
REFERENCE "RFC 4601 section 4.3.1"
::= { pimNeighborEntry 5 }
pimNeighborUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this PIM neighbor (last) became a neighbor
of the local router."
::= { pimNeighborEntry 6 }
pimNeighborExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum time remaining before this PIM neighbor will
time out. The value zero indicates that this PIM neighbor
will never time out."
::= { pimNeighborEntry 7 }
pimNeighborDRPriorityPresent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Evaluates to TRUE if this neighbor is using the DR Priority
option."
REFERENCE "RFC 4601 section 4.3.2"
::= { pimNeighborEntry 8 }
pimNeighborDRPriority OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the Designated Router Priority from the last
PIM Hello message received from this neighbor. This object
is always zero if pimNeighborDRPriorityPresent is FALSE."
REFERENCE "RFC 4601 section 4.3.2"
::= { pimNeighborEntry 9 }
pimNeighborLanPruneDelayPresent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Evaluates to TRUE if this neighbor is using the LAN Prune
Delay option."
REFERENCE "RFC 4601 section 4.3.3"
::= { pimNeighborEntry 10 }
pimNeighborTBit OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the T bit was set in the LAN Prune Delay option
received from this neighbor. The T bit specifies the
ability of the neighbor to disable join suppression. This
object is always TRUE if pimNeighborLanPruneDelayPresent is
FALSE."
REFERENCE "RFC 4601 section 4.3.3"
::= { pimNeighborEntry 11 }
pimNeighborPropagationDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..32767)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the Propagation_Delay field of the LAN Prune
Delay option received from this neighbor. This object is
always zero if pimNeighborLanPruneDelayPresent is FALSE."
REFERENCE "RFC 4601 section 4.3.3"
::= { pimNeighborEntry 12 }
pimNeighborOverrideInterval OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the Override_Interval field of the LAN Prune
Delay option received from this neighbor. This object is
always zero if pimNeighborLanPruneDelayPresent is FALSE."
REFERENCE "RFC 4601 section 4.3.3"
::= { pimNeighborEntry 13 }
pimNeighborBidirCapable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Evaluates to TRUE if this neighbor is using the
Bidirectional-PIM Capable option."
REFERENCE "RFC 5015 section 3.2 and 3.7.4"
::= { pimNeighborEntry 14 }
pimNeighborSRCapable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Evaluates to TRUE if this neighbor is using the State
Refresh Capable option. This object is used only by
PIM-DM."
REFERENCE "RFC 3973 section 4.3.4"
::= { pimNeighborEntry 15 }
-- -- The PIM Neighbor Secondary Address Table --
pimNbrSecAddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimNbrSecAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the secondary addresses
advertised by each PIM neighbor (on a subset of the rows of
the pimNeighborTable defined above)."
REFERENCE "RFC 4601 section 4.3.4"
::= { pim 3 }
pimNbrSecAddressEntry OBJECT-TYPE
SYNTAX PimNbrSecAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimNbrSecAddressTable."
INDEX { pimNbrSecAddressIfIndex,
pimNbrSecAddressType,
pimNbrSecAddressPrimary,
pimNbrSecAddress }
::= { pimNbrSecAddressTable 1 }
PimNbrSecAddressEntry ::= SEQUENCE {
pimNbrSecAddressIfIndex InterfaceIndex, pimNbrSecAddressType InetAddressType, pimNbrSecAddressPrimary InetAddress, pimNbrSecAddress InetAddress
}
pimNbrSecAddressIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of ifIndex for the interface used to reach this
PIM neighbor."
::= { pimNbrSecAddressEntry 1 }
pimNbrSecAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of this PIM neighbor."
::= { pimNbrSecAddressEntry 2 }
pimNbrSecAddressPrimary OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The primary IP address of this PIM neighbor. The
InetAddressType is given by the pimNbrSecAddressType
object."
::= { pimNbrSecAddressEntry 3 }
pimNbrSecAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The secondary IP address of this PIM neighbor. The
InetAddressType is given by the pimNbrSecAddressType
object."
::= { pimNbrSecAddressEntry 4 }
-- -- The PIM (*,G) State Table --
pimStarGTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimStarGEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the non-interface specific
(*,G) state that PIM has."
REFERENCE "RFC 4601 section 4.1.3"
::= { pim 4 }
pimStarGEntry OBJECT-TYPE
SYNTAX PimStarGEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimStarGTable."
INDEX { pimStarGAddressType,
pimStarGGrpAddress }
::= { pimStarGTable 1 }
PimStarGEntry ::= SEQUENCE {
pimStarGAddressType InetAddressType, pimStarGGrpAddress InetAddress, pimStarGUpTime TimeTicks, pimStarGPimMode PimMode, pimStarGRPAddressType InetAddressType, pimStarGRPAddress InetAddress, pimStarGPimModeOrigin PimGroupMappingOriginType, pimStarGRPIsLocal TruthValue, pimStarGUpstreamJoinState INTEGER, pimStarGUpstreamJoinTimer TimeTicks, pimStarGUpstreamNeighborType InetAddressType, pimStarGUpstreamNeighbor InetAddress, pimStarGRPFIfIndex InterfaceIndexOrZero, pimStarGRPFNextHopType InetAddressType, pimStarGRPFNextHop InetAddress, pimStarGRPFRouteProtocol IANAipRouteProtocol, pimStarGRPFRouteAddress InetAddress, pimStarGRPFRoutePrefixLength InetAddressPrefixLength, pimStarGRPFRouteMetricPref Unsigned32, pimStarGRPFRouteMetric Unsigned32
}
pimStarGAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of this multicast group."
::= { pimStarGEntry 1 }
pimStarGGrpAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group address. The InetAddressType is given
by the pimStarGAddressType object."
::= { pimStarGEntry 2 }
pimStarGUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this entry was created by the local router."
::= { pimStarGEntry 3 }
pimStarGPimMode OBJECT-TYPE
SYNTAX PimMode { asm(3), bidir(4) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether this entry represents an ASM (Any Source Multicast,
used with PIM-SM) or BIDIR-PIM group."
::= { pimStarGEntry 4 }
pimStarGRPAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of the Rendezvous Point (RP), or
unknown(0) if the RP address is unknown."
::= { pimStarGEntry 5 }
pimStarGRPAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the Rendezvous Point (RP) for the group.
The InetAddressType is given by the pimStarGRPAddressType."
::= { pimStarGEntry 6 }
pimStarGPimModeOrigin OBJECT-TYPE
SYNTAX PimGroupMappingOriginType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The mechanism by which the PIM mode and RP for the group
were learned."
::= { pimStarGEntry 7 }
pimStarGRPIsLocal OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the local router is the RP for the group."
::= { pimStarGEntry 8 }
pimStarGUpstreamJoinState OBJECT-TYPE
SYNTAX INTEGER {
notJoined (1),
joined (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the local router should join the RP tree for the
group. This corresponds to the state of the upstream (*,G)
state machine in the PIM-SM specification."
REFERENCE "RFC 4601 section 4.5.6"
::= { pimStarGEntry 9 }
pimStarGUpstreamJoinTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before the local router next sends a
periodic (*,G) Join message on pimStarGRPFIfIndex. This
timer is called the (*,G) Upstream Join Timer in the PIM-SM
specification. This object is zero if the timer is not
running."
REFERENCE "RFC 4601 section 4.10"
::= { pimStarGEntry 10 }
pimStarGUpstreamNeighborType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary address type of the upstream neighbor, or
unknown(0) if the upstream neighbor address is unknown or is
not a PIM neighbor."
::= { pimStarGEntry 11 }
pimStarGUpstreamNeighbor OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary address of the neighbor on pimStarGRPFIfIndex
that the local router is sending periodic (*,G) Join
messages to. The InetAddressType is given by the
pimStarGUpstreamNeighborType object. This address is called
RPF'(*,G) in the PIM-SM specification."
REFERENCE "RFC 4601 section 4.1.6"
::= { pimStarGEntry 12 }
pimStarGRPFIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ifIndex for the Reverse Path Forwarding
(RPF) interface towards the RP, or zero if the RPF
interface is unknown."
::= { pimStarGEntry 13 }
pimStarGRPFNextHopType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of the RPF next hop towards the RP, or
unknown(0) if the RPF next hop is unknown."
::= { pimStarGEntry 14 }
pimStarGRPFNextHop OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the RPF next hop towards the RP. The
InetAddressType is given by the pimStarGRPFNextHopType
object. This address is called MRIB.next_hop(RP(G))
in the PIM-SM specification."
REFERENCE "RFC 4601 section 4.5.5"
::= { pimStarGEntry 15 }
pimStarGRPFRouteProtocol OBJECT-TYPE
SYNTAX IANAipRouteProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The routing mechanism via which the route used to find the
RPF interface towards the RP was learned."
::= { pimStarGEntry 16 }
pimStarGRPFRouteAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address that, when combined with the corresponding
value of pimStarGRPFRoutePrefixLength, identifies the route
used to find the RPF interface towards the RP. The
InetAddressType is given by the pimStarGRPFNextHopType
object.
This address object is only significant up to
pimStarGRPFRoutePrefixLength bits. The remainder of the
address bits are zero."
::= { pimStarGEntry 17 }
pimStarGRPFRoutePrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The prefix length that, when combined with the
corresponding value of pimStarGRPFRouteAddress, identifies
the route used to find the RPF interface towards the RP.
The InetAddressType is given by the pimStarGRPFNextHopType
object."
::= { pimStarGEntry 18 }
pimStarGRPFRouteMetricPref OBJECT-TYPE
SYNTAX Unsigned32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The metric preference of the route used to find the RPF
interface towards the RP."
::= { pimStarGEntry 19 }
pimStarGRPFRouteMetric OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The routing metric of the route used to find the RPF
interface towards the RP."
::= { pimStarGEntry 20 }
-- -- The PIM (*,G,I) State Table --
pimStarGITable OBJECT-TYPE
SYNTAX SEQUENCE OF PimStarGIEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the interface-specific (*,G)
state that PIM has."
REFERENCE "RFC 4601 section 4.1.3"
::= { pim 5 }
pimStarGIEntry OBJECT-TYPE
SYNTAX PimStarGIEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimStarGITable."
INDEX { pimStarGAddressType,
pimStarGGrpAddress,
pimStarGIIfIndex }
::= { pimStarGITable 1 }
PimStarGIEntry ::= SEQUENCE {
pimStarGIIfIndex InterfaceIndex, pimStarGIUpTime TimeTicks, pimStarGILocalMembership TruthValue, pimStarGIJoinPruneState INTEGER, pimStarGIPrunePendingTimer TimeTicks, pimStarGIJoinExpiryTimer TimeTicks, pimStarGIAssertState INTEGER, pimStarGIAssertTimer TimeTicks, pimStarGIAssertWinnerAddressType InetAddressType, pimStarGIAssertWinnerAddress InetAddress, pimStarGIAssertWinnerMetricPref Unsigned32, pimStarGIAssertWinnerMetric Unsigned32
}
pimStarGIIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex of the interface that this entry corresponds
to."
::= { pimStarGIEntry 1 }
pimStarGIUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this entry was created by the local router."
::= { pimStarGIEntry 2 }
pimStarGILocalMembership OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the local router has (*,G) local membership on this
interface (resulting from a mechanism such as IGMP or MLD).
This corresponds to local_receiver_include(*,G,I) in the
PIM-SM specification."
REFERENCE "RFC 3376, RFC 3810, and RFC 4601 section 4.1.6"
::= { pimStarGIEntry 3 }
pimStarGIJoinPruneState OBJECT-TYPE
SYNTAX INTEGER {
noInfo (1),
join (2),
prunePending (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state resulting from (*,G) Join/Prune messages
received on this interface. This corresponds to the state
of the downstream per-interface (*,G) state machine in the
PIM-SM specification."
REFERENCE "RFC 4601 section 4.5.2"
::= { pimStarGIEntry 4 }
pimStarGIPrunePendingTimer OBJECT-TYPE
SYNTAX TimeTicks MAX-ACCESS read-only STATUS current
DESCRIPTION
"The time remaining before the local router acts on a (*,G)
Prune message received on this interface, during which the
router is waiting to see whether another downstream router
will override the Prune message. This timer is called the
(*,G) Prune-Pending Timer in the PIM-SM specification. This
object is zero if the timer is not running."
REFERENCE "RFC 4601 section 4.5.1"
::= { pimStarGIEntry 5 }
pimStarGIJoinExpiryTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before (*,G) Join state for this
interface expires. This timer is called the (*,G) Join
Expiry Timer in the PIM-SM specification. This object is
zero if the timer is not running. A value of 'FFFFFFFF'h
indicates an infinite expiry time."
REFERENCE "RFC 4601 section 4.10"
::= { pimStarGIEntry 6 }
pimStarGIAssertState OBJECT-TYPE
SYNTAX INTEGER {
noInfo (1),
iAmAssertWinner (2),
iAmAssertLoser (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The (*,G) Assert state for this interface. This
corresponds to the state of the per-interface (*,G) Assert
state machine in the PIM-SM specification. If
pimStarGPimMode is 'bidir', this object must be 'noInfo'."
REFERENCE "RFC 4601 section 4.6.2"
::= { pimStarGIEntry 7 }
pimStarGIAssertTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimStarGIAssertState is 'iAmAssertWinner', this is the
time remaining before the local router next sends a (*,G)
Assert message on this interface. If pimStarGIAssertState
is 'iAmAssertLoser', this is the time remaining before the
(*,G) Assert state expires. If pimStarGIAssertState is
'noInfo', this is zero. This timer is called the (*,G)
Assert Timer in the PIM-SM specification."
REFERENCE "RFC 4601 section 4.6.2"
::= { pimStarGIEntry 8 }
pimStarGIAssertWinnerAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimStarGIAssertState is 'iAmAssertLoser', this is the
address type of the assert winner; otherwise, this object is
unknown(0)."
::= { pimStarGIEntry 9 }
pimStarGIAssertWinnerAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimStarGIAssertState is 'iAmAssertLoser', this is the
address of the assert winner. The InetAddressType is given
by the pimStarGIAssertWinnerAddressType object."
::= { pimStarGIEntry 10 }
pimStarGIAssertWinnerMetricPref OBJECT-TYPE
SYNTAX Unsigned32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimStarGIAssertState is 'iAmAssertLoser', this is the
metric preference of the route to the RP advertised by the
assert winner; otherwise, this object is zero."
::= { pimStarGIEntry 11 }
pimStarGIAssertWinnerMetric OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimStarGIAssertState is 'iAmAssertLoser', this is the
routing metric of the route to the RP advertised by the
assert winner; otherwise, this object is zero."
::= { pimStarGIEntry 12 }
-- -- The PIM (S,G) State Table
--
pimSGTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimSGEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the non-interface specific
(S,G) state that PIM has."
REFERENCE "RFC 4601 section 4.1.4"
::= { pim 6 }
pimSGEntry OBJECT-TYPE
SYNTAX PimSGEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimSGTable."
INDEX { pimSGAddressType,
pimSGGrpAddress,
pimSGSrcAddress }
::= { pimSGTable 1 }
PimSGEntry ::= SEQUENCE {
pimSGAddressType InetAddressType, pimSGGrpAddress InetAddress, pimSGSrcAddress InetAddress, pimSGUpTime TimeTicks, pimSGPimMode PimMode, pimSGUpstreamJoinState INTEGER, pimSGUpstreamJoinTimer TimeTicks, pimSGUpstreamNeighbor InetAddress, pimSGRPFIfIndex InterfaceIndexOrZero, pimSGRPFNextHopType InetAddressType, pimSGRPFNextHop InetAddress, pimSGRPFRouteProtocol IANAipRouteProtocol, pimSGRPFRouteAddress InetAddress, pimSGRPFRoutePrefixLength InetAddressPrefixLength, pimSGRPFRouteMetricPref Unsigned32, pimSGRPFRouteMetric Unsigned32, pimSGSPTBit TruthValue, pimSGKeepaliveTimer TimeTicks, pimSGDRRegisterState INTEGER, pimSGDRRegisterStopTimer TimeTicks, pimSGRPRegisterPMBRAddressType InetAddressType, pimSGRPRegisterPMBRAddress InetAddress, pimSGUpstreamPruneState INTEGER, pimSGUpstreamPruneLimitTimer TimeTicks,
pimSGOriginatorState INTEGER, pimSGSourceActiveTimer TimeTicks, pimSGStateRefreshTimer TimeTicks
}
pimSGAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of the source and multicast group for this
entry."
::= { pimSGEntry 1 }
pimSGGrpAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group address for this entry. The
InetAddressType is given by the pimSGAddressType object."
::= { pimSGEntry 2 }
pimSGSrcAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The source address for this entry. The InetAddressType is
given by the pimSGAddressType object."
::= { pimSGEntry 3 }
pimSGUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this entry was created by the local router."
::= { pimSGEntry 4 }
pimSGPimMode OBJECT-TYPE
SYNTAX PimMode { ssm(2), asm(3) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether pimSGGrpAddress is an SSM (Source Specific
Multicast, used with PIM-SM) or ASM (Any Source Multicast,
used with PIM-SM) group."
REFERENCE "RFC 4601 section 4.5.2, RFC 3569, and 'IP Multicast MIB' (August 2007) ipMcastSsmRangeTable" ::= { pimSGEntry 5 }
pimSGUpstreamJoinState OBJECT-TYPE
SYNTAX INTEGER {
notJoined (1),
joined (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the local router should join the shortest-path tree
for the source and group represented by this entry. This
corresponds to the state of the upstream (S,G) state machine
in the PIM-SM specification."
REFERENCE "RFC 4601 section 4.5.7"
::= { pimSGEntry 6 }
pimSGUpstreamJoinTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before the local router next sends a
periodic (S,G) Join message on pimSGRPFIfIndex. This timer
is called the (S,G) Upstream Join Timer in the PIM-SM
specification. This object is zero if the timer is not
running."
REFERENCE "RFC 4601 sections 4.10 and 4.11"
::= { pimSGEntry 7 }
pimSGUpstreamNeighbor OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary address of the neighbor on pimSGRPFIfIndex that
the local router is sending periodic (S,G) Join messages to.
This is zero if the RPF next hop is unknown or is not a
PIM neighbor. The InetAddressType is given by the
pimSGAddressType object. This address is called RPF'(S,G)
in the PIM-SM specification."
REFERENCE "RFC 4601 section 4.1.6"
::= { pimSGEntry 8 }
pimSGRPFIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ifIndex for the RPF interface towards the
source, or zero if the RPF interface is unknown."
::= { pimSGEntry 9 }
pimSGRPFNextHopType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of the RPF next hop towards the source, or
unknown(0) if the RPF next hop is unknown."
::= { pimSGEntry 10 }
pimSGRPFNextHop OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the RPF next hop towards the source. The
InetAddressType is given by the pimSGRPFNextHopType. This
address is called MRIB.next_hop(S) in the PIM-SM
specification."
REFERENCE "RFC 4601 section 4.5.5"
::= { pimSGEntry 11 }
pimSGRPFRouteProtocol OBJECT-TYPE
SYNTAX IANAipRouteProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The routing mechanism via which the route used to find the
RPF interface towards the source was learned."
::= { pimSGEntry 12 }
pimSGRPFRouteAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address that, when combined with the corresponding
value of pimSGRPFRoutePrefixLength, identifies the route
used to find the RPF interface towards the source. The
InetAddressType is given by the pimSGRPFNextHopType object.
This address object is only significant up to
pimSGRPFRoutePrefixLength bits. The remainder of the
address bits are zero."
::= { pimSGEntry 13 }
pimSGRPFRoutePrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The prefix length that, when combined with the
corresponding value of pimSGRPFRouteAddress, identifies the
route used to find the RPF interface towards the source.
The InetAddressType is given by the pimSGRPFNextHopType
object."
::= { pimSGEntry 14 }
pimSGRPFRouteMetricPref OBJECT-TYPE
SYNTAX Unsigned32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The metric preference of the route used to find the RPF
interface towards the source."
::= { pimSGEntry 15 }
pimSGRPFRouteMetric OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The routing metric of the route used to find the RPF
interface towards the source."
::= { pimSGEntry 16 }
pimSGSPTBit OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the SPT bit is set; and therefore whether
forwarding is taking place on the shortest-path tree."
::= { pimSGEntry 17 }
pimSGKeepaliveTimer OBJECT-TYPE
SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION
"The time remaining before this (S,G) state expires, in
the absence of explicit (S,G) local membership or (S,G)
Join messages received to maintain it. This timer is
called the (S,G) Keepalive Timer in the PIM-SM
specification."
REFERENCE "RFC 4601 section 4.1.4"
::= { pimSGEntry 18 }
pimSGDRRegisterState OBJECT-TYPE
SYNTAX INTEGER {
noInfo (1),
join (2),
joinPending (3),
prune (4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the local router should encapsulate (S,G) data
packets in Register messages and send them to the RP. This
corresponds to the state of the per-(S,G) Register state
machine in the PIM-SM specification. This object is always
'noInfo' unless pimSGPimMode is 'asm'."
REFERENCE "RFC 4601 section 4.4.1"
::= { pimSGEntry 19 }
pimSGDRRegisterStopTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimSGDRRegisterState is 'prune', this is the time
remaining before the local router sends a Null-Register
message to the RP. If pimSGDRRegisterState is
'joinPending', this is the time remaining before the local
router resumes encapsulating data packets and sending them
to the RP. Otherwise, this is zero. This timer is called
the Register-Stop Timer in the PIM-SM specification."
REFERENCE "RFC 4601 section 4.4"
::= { pimSGEntry 20 }
pimSGRPRegisterPMBRAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of the first PIM Multicast Border Router
to send a Register message with the Border bit set. This
object is unknown(0) if the local router is not the RP for
the group."
::= { pimSGEntry 21 }
pimSGRPRegisterPMBRAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of the first PIM Multicast Border Router to
send a Register message with the Border bit set. The
InetAddressType is given by the
pimSGRPRegisterPMBRAddressType object."
::= { pimSGEntry 22 }
pimSGUpstreamPruneState OBJECT-TYPE
SYNTAX INTEGER {
forwarding (1),
ackpending (2),
pruned (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the local router has pruned itself from the tree.
This corresponds to the state of the upstream prune (S,G)
state machine in the PIM-DM specification. This object is
used only by PIM-DM."
REFERENCE "RFC 3973 section 4.4.1"
::= { pimSGEntry 23 }
pimSGUpstreamPruneLimitTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before the local router may send a (S,G)
Prune message on pimSGRPFIfIndex. This timer is called the
(S,G) Prune Limit Timer in the PIM-DM specification. This
object is zero if the timer is not running. This object is
used only by PIM-DM."
REFERENCE "RFC 2973 section 4.8"
::= { pimSGEntry 24 }
pimSGOriginatorState OBJECT-TYPE
SYNTAX INTEGER {
notOriginator (1),
originator (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the router is an originator for an (S,G) message
flow. This corresponds to the state of the per-(S,G)
Originator state machine in the PIM-DM specification. This
object is used only by PIM-DM."
REFERENCE "RFC 3973 section 4.5.2"
::= { pimSGEntry 25 }
pimSGSourceActiveTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimSGOriginatorState is 'originator', this is the time
remaining before the local router reverts to a notOriginator
state. Otherwise, this is zero. This timer is called the
Source Active Timer in the PIM-DM specification. This
object is used only by PIM-DM."
REFERENCE "RFC 3973 section 4.8"
::= { pimSGEntry 26 }
pimSGStateRefreshTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimSGOriginatorState is 'originator', this is the time
remaining before the local router sends a State Refresh
message. Otherwise, this is zero. This timer is called the
State Refresh Timer in the PIM-DM specification. This
object is used only by PIM-DM."
REFERENCE "RFC 3973 section 4.8"
::= { pimSGEntry 27 }
-- -- The PIM (S,G,I) State Table --
pimSGITable OBJECT-TYPE
SYNTAX SEQUENCE OF PimSGIEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the interface-specific (S,G)
state that PIM has."
REFERENCE "RFC 4601 section 4.1.4" ::= { pim 7 }
pimSGIEntry OBJECT-TYPE
SYNTAX PimSGIEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimSGITable."
INDEX { pimSGAddressType,
pimSGGrpAddress,
pimSGSrcAddress,
pimSGIIfIndex }
::= { pimSGITable 1 }
PimSGIEntry ::= SEQUENCE {
pimSGIIfIndex InterfaceIndex, pimSGIUpTime TimeTicks, pimSGILocalMembership TruthValue, pimSGIJoinPruneState INTEGER, pimSGIPrunePendingTimer TimeTicks, pimSGIJoinExpiryTimer TimeTicks, pimSGIAssertState INTEGER, pimSGIAssertTimer TimeTicks, pimSGIAssertWinnerAddressType InetAddressType, pimSGIAssertWinnerAddress InetAddress, pimSGIAssertWinnerMetricPref Unsigned32, pimSGIAssertWinnerMetric Unsigned32
}
pimSGIIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex of the interface that this entry corresponds
to."
::= { pimSGIEntry 1 }
pimSGIUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this entry was created by the local router."
::= { pimSGIEntry 2 }
pimSGILocalMembership OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the local router has (S,G) local membership on this
interface (resulting from a mechanism such as IGMP or MLD).
This corresponds to local_receiver_include(S,G,I) in the
PIM-SM specification."
REFERENCE "RFC 3376, RFC 3810, RFC 4601 sections 4.1.6, 4.6.1, and
4.6.2"
::= { pimSGIEntry 3 }
pimSGIJoinPruneState OBJECT-TYPE
SYNTAX INTEGER {
noInfo (1),
join (2),
prunePending (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state resulting from (S,G) Join/Prune messages
received on this interface. This corresponds to the state
of the downstream per-interface (S,G) state machine in the
PIM-SM and PIM-DM specification."
REFERENCE "RFC 4601 section 4.5.3 and RFC 3973 section 4.4.2"
::= { pimSGIEntry 4 }
pimSGIPrunePendingTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before the local router acts on an (S,G)
Prune message received on this interface, during which the
router is waiting to see whether another downstream router
will override the Prune message. This timer is called the
(S,G) Prune-Pending Timer in the PIM-SM specification. This
object is zero if the timer is not running."
REFERENCE "RFC 4601 sections 4.5.3 and 4.5.4"
::= { pimSGIEntry 5 }
pimSGIJoinExpiryTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before (S,G) Join state for this
interface expires. This timer is called the (S,G) Join
Expiry Timer in the PIM-SM specification. This object is
zero if the timer is not running. A value of 'FFFFFFFF'h
indicates an infinite expiry time. This timer is called the
(S,G) Prune Timer in the PIM-DM specification."
REFERENCE "RFC 4601 section 4.10 and RFC 3973 section 4.8"
::= { pimSGIEntry 6 }
pimSGIAssertState OBJECT-TYPE
SYNTAX INTEGER {
noInfo (1),
iAmAssertWinner (2),
iAmAssertLoser (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The (S,G) Assert state for this interface. This
corresponds to the state of the per-interface (S,G) Assert
state machine in the PIM-SM specification."
REFERENCE "RFC 4601 section 4.6.1"
::= { pimSGIEntry 7 }
pimSGIAssertTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimSGIAssertState is 'iAmAssertWinner', this is the time
remaining before the local router next sends a (S,G) Assert
message on this interface. If pimSGIAssertState is
'iAmAssertLoser', this is the time remaining before the
(S,G) Assert state expires. If pimSGIAssertState is
'noInfo', this is zero. This timer is called the (S,G)
Assert Timer in the PIM-SM specification."
REFERENCE "RFC 4601 section 4.6.1"
::= { pimSGIEntry 8 }
pimSGIAssertWinnerAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimSGIAssertState is 'iAmAssertLoser', this is the
address type of the assert winner; otherwise, this object is
unknown(0)."
::= { pimSGIEntry 9 }
pimSGIAssertWinnerAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimSGIAssertState is 'iAmAssertLoser', this is the
address of the assert winner. The InetAddressType is given
by the pimSGIAssertWinnerAddressType object."
::= { pimSGIEntry 10 }
pimSGIAssertWinnerMetricPref OBJECT-TYPE
SYNTAX Unsigned32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimSGIAssertState is 'iAmAssertLoser', this is the
metric preference of the route to the source advertised by
the assert winner; otherwise, this object is zero."
::= { pimSGIEntry 11 }
pimSGIAssertWinnerMetric OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If pimSGIAssertState is 'iAmAssertLoser', this is the
routing metric of the route to the source advertised by the
assert winner; otherwise, this object is zero."
::= { pimSGIEntry 12 }
-- -- The PIM (S,G,rpt) State Table --
pimSGRptTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimSGRptEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the non-interface specific
(S,G,rpt) state that PIM has."
REFERENCE "RFC 4601 section 4.1.5"
::= { pim 8 }
pimSGRptEntry OBJECT-TYPE
SYNTAX PimSGRptEntry MAX-ACCESS not-accessible STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimSGRptTable."
INDEX { pimStarGAddressType,
pimStarGGrpAddress,
pimSGRptSrcAddress }
::= { pimSGRptTable 1 }
PimSGRptEntry ::= SEQUENCE {
pimSGRptSrcAddress InetAddress, pimSGRptUpTime TimeTicks, pimSGRptUpstreamPruneState INTEGER, pimSGRptUpstreamOverrideTimer TimeTicks
}
pimSGRptSrcAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The source address for this entry. The InetAddressType is
given by the pimStarGAddressType object."
::= { pimSGRptEntry 1 }
pimSGRptUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this entry was created by the local router."
::= { pimSGRptEntry 2 }
pimSGRptUpstreamPruneState OBJECT-TYPE
SYNTAX INTEGER {
rptNotJoined (1),
pruned (2),
notPruned (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the local router should prune the source off the RP
tree. This corresponds to the state of the upstream
(S,G,rpt) state machine for triggered messages in the PIM-SM
specification."
REFERENCE "RFC 4601 section 4.5.9"
::= { pimSGRptEntry 3 }
pimSGRptUpstreamOverrideTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before the local router sends a
triggered (S,G,rpt) Join message on pimStarGRPFIfIndex.
This timer is called the (S,G,rpt) Upstream Override Timer
in the PIM-SM specification. This object is zero if the
timer is not running."
REFERENCE "RFC 4601 section 4.5.9"
::= { pimSGRptEntry 4 }
-- -- The PIM (S,G,rpt,I) State Table --
pimSGRptITable OBJECT-TYPE
SYNTAX SEQUENCE OF PimSGRptIEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the interface-specific
(S,G,rpt) state that PIM has."
REFERENCE "RFC 4601 section 4.1.5"
::= { pim 9 }
pimSGRptIEntry OBJECT-TYPE
SYNTAX PimSGRptIEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimSGRptITable."
INDEX { pimStarGAddressType,
pimStarGGrpAddress,
pimSGRptSrcAddress,
pimSGRptIIfIndex }
::= { pimSGRptITable 1 }
PimSGRptIEntry ::= SEQUENCE {
pimSGRptIIfIndex InterfaceIndex, pimSGRptIUpTime TimeTicks, pimSGRptILocalMembership TruthValue, pimSGRptIJoinPruneState INTEGER, pimSGRptIPrunePendingTimer TimeTicks, pimSGRptIPruneExpiryTimer TimeTicks
}
pimSGRptIIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex of the interface that this entry corresponds
to."
::= { pimSGRptIEntry 1 }
pimSGRptIUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this entry was created by the local router."
::= { pimSGRptIEntry 2 }
pimSGRptILocalMembership OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the local router has both (*,G) include local
membership and (S,G) exclude local membership on this
interface (resulting from a mechanism such as IGMP or MLD).
This corresponds to local_receiver_exclude(S,G,I) in the
PIM-SM specification."
REFERENCE "RFC 3376, RFC 3810, RFC 4601 section 4.1.6"
::= { pimSGRptIEntry 3 }
pimSGRptIJoinPruneState OBJECT-TYPE
SYNTAX INTEGER {
noInfo (1),
prune (2),
prunePending (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state resulting from (S,G,rpt) Join/Prune messages
received on this interface. This corresponds to the state
of the downstream per-interface (S,G,rpt) state machine in
the PIM-SM specification."
REFERENCE "RFC 4601 section 4.5.4"
::= { pimSGRptIEntry 4 }
pimSGRptIPrunePendingTimer OBJECT-TYPE
SYNTAX TimeTicks MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before the local router starts pruning
this source off the RP tree. This timer is called the
(S,G,rpt) Prune-Pending Timer in the PIM-SM specification.
This object is zero if the timer is not running."
REFERENCE "RFC 4601 section 4.5.4"
::= { pimSGRptIEntry 5 }
pimSGRptIPruneExpiryTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before (S,G,rpt) Prune state for this
interface expires. This timer is called the (S,G,rpt)
Prune Expiry Timer in the PIM-SM specification. This object
is zero if the timer is not running. A value of 'FFFFFFFF'h
indicates an infinite expiry time."
REFERENCE "RFC 4601 section 4.5.4"
::= { pimSGRptIEntry 6 }
-- -- The PIM Bidir DF-Election Table --
pimBidirDFElectionTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimBidirDFElectionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the per-RP Designated
Forwarder (DF) Election state for each interface for all the
RPs in BIDIR mode."
REFERENCE "RFC 5015 section 3.5"
::= { pim 10 }
pimBidirDFElectionEntry OBJECT-TYPE
SYNTAX PimBidirDFElectionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimBidirDFElectionTable."
INDEX { pimBidirDFElectionAddressType,
pimBidirDFElectionRPAddress,
pimBidirDFElectionIfIndex }
::= { pimBidirDFElectionTable 1 }
PimBidirDFElectionEntry ::= SEQUENCE {
pimBidirDFElectionAddressType InetAddressType, pimBidirDFElectionRPAddress InetAddress, pimBidirDFElectionIfIndex InterfaceIndex, pimBidirDFElectionWinnerAddressType InetAddressType, pimBidirDFElectionWinnerAddress InetAddress, pimBidirDFElectionWinnerUpTime TimeTicks, pimBidirDFElectionWinnerMetricPref Unsigned32, pimBidirDFElectionWinnerMetric Unsigned32, pimBidirDFElectionState INTEGER, pimBidirDFElectionStateTimer TimeTicks
}
pimBidirDFElectionAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of the RP for which the DF state is being
maintained."
::= { pimBidirDFElectionEntry 1 }
pimBidirDFElectionRPAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the RP for which the DF state is being
maintained. The InetAddressType is given by the
pimBidirDFElectionAddressType object."
::= { pimBidirDFElectionEntry 2 }
pimBidirDFElectionIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of ifIndex for the interface for which the DF
state is being maintained."
::= { pimBidirDFElectionEntry 3 }
pimBidirDFElectionWinnerAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary address type of the winner of the DF Election
process. A value of unknown(0) indicates there is currently
no DF."
::= { pimBidirDFElectionEntry 4 }
pimBidirDFElectionWinnerAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary IP address of the winner of the DF Election
process. The InetAddressType is given by the
pimBidirDFElectionWinnerAddressType object."
::= { pimBidirDFElectionEntry 5 }
pimBidirDFElectionWinnerUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since the current winner (last) became elected as
the DF for this RP."
::= { pimBidirDFElectionEntry 6 }
pimBidirDFElectionWinnerMetricPref OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The metric preference advertised by the DF Winner, or zero
if there is currently no DF."
::= { pimBidirDFElectionEntry 7 }
pimBidirDFElectionWinnerMetric OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The metric advertised by the DF Winner, or zero if there is
currently no DF."
::= { pimBidirDFElectionEntry 8 }
pimBidirDFElectionState OBJECT-TYPE
SYNTAX INTEGER {
dfOffer(1),
dfLose(2),
dfWinner(3),
dfBackoff(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of this interface with respect to DF-Election for
this RP. The states correspond to the ones defined in the
BIDIR-PIM specification."
REFERENCE "RFC 5015 section 3.5.3.1"
::= { pimBidirDFElectionEntry 9 }
pimBidirDFElectionStateTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum time remaining after which the local router
will expire the current DF state represented by
pimBidirDFElectionState."
::= { pimBidirDFElectionEntry 10 }
-- -- The PIM Static RP Table --
pimStaticRPTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimStaticRPEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to manage static configuration of RPs.
If the group prefixes configured for two or more rows in
this table overlap, the row with the greatest value of
pimStaticRPGrpPrefixLength is used for the overlapping
range."
REFERENCE "RFC 4601 section 3.7"
::= { pim 11 }
pimStaticRPEntry OBJECT-TYPE
SYNTAX PimStaticRPEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimStaticRPTable. This
entry is preserved on agent restart."
INDEX { pimStaticRPAddressType,
pimStaticRPGrpAddress,
pimStaticRPGrpPrefixLength }
::= { pimStaticRPTable 1 }
PimStaticRPEntry ::= SEQUENCE {
pimStaticRPAddressType InetAddressType, pimStaticRPGrpAddress InetAddress, pimStaticRPGrpPrefixLength InetAddressPrefixLength, pimStaticRPRPAddress InetAddress, pimStaticRPPimMode PimMode, pimStaticRPOverrideDynamic TruthValue, pimStaticRPPrecedence Unsigned32, pimStaticRPRowStatus RowStatus, pimStaticRPStorageType StorageType
}
pimStaticRPAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of this entry."
::= { pimStaticRPEntry 1 }
pimStaticRPGrpAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group address that, when combined with
pimStaticRPGrpPrefixLength, gives the group prefix for this
entry. The InetAddressType is given by the
pimStaticRPAddressType object.
This address object is only significant up to
pimStaticRPGrpPrefixLength bits. The remainder of the
address bits are zero. This is especially important for
this index field, which is part of the index of this entry.
Any non-zero bits would signify an entirely different
entry."
::= { pimStaticRPEntry 2 }
pimStaticRPGrpPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength (4..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group prefix length that, when combined
with pimStaticRPGrpAddress, gives the group prefix for this
entry. The InetAddressType is given by the
pimStaticRPAddressType object. If pimStaticRPAddressType is
'ipv4' or 'ipv4z', this object must be in the range 4..32.
If pimStaticRPGrpAddressType is 'ipv6' or 'ipv6z', this
object must be in the range 8..128."
::= { pimStaticRPEntry 3 }
pimStaticRPRPAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The IP address of the RP to be used for groups within this
group prefix. The InetAddressType is given by the
pimStaticRPAddressType object."
::= { pimStaticRPEntry 4 }
pimStaticRPPimMode OBJECT-TYPE
SYNTAX PimMode { ssm(2), asm(3), bidir(4) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The PIM mode to be used for groups in this group prefix.
If this object is set to ssm(2), then pimStaticRPRPAddress
must be set to zero. No RP operations are ever possible for
PIM Mode SSM."
REFERENCE "RFC 4601 section 3.7, RFC 3569, and
'IP Multicast MIB' (August 2007) ipMcastSsmRangeTable"
DEFVAL { asm }
::= { pimStaticRPEntry 5 }
pimStaticRPOverrideDynamic OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Whether this static RP configuration will override other
group mappings in this group prefix. If this object is
TRUE, then it will override:
- RP information learned dynamically for groups in this
group prefix.
- RP information configured in pimStaticRPTable with
pimStaticRPOverrideDynamic set to FALSE.
See pimGroupMappingTable for details."
DEFVAL { false }
::= { pimStaticRPEntry 6 }
pimStaticRPPrecedence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value for pimGroupMappingPrecedence to be used for this
static RP configuration. This allows fine control over
which configuration is overridden by this static
configuration.
If pimStaticRPOverrideDynamic is set to TRUE, all dynamic RP
configuration is overridden by this static configuration,
whatever the value of this object.
The absolute values of this object have a significance only
on the local router and do not need to be coordinated with
other routers. A setting of this object may have different
effects when applied to other routers.
Do not use this object unless fine control of static RP
behavior on the local router is required."
::= { pimStaticRPEntry 7 }
pimStaticRPRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row, by which rows in this table can
be created and destroyed.
This status object cannot be set to active(1) before a valid
value has been written to pimStaticRPRPAddress.
All writeable objects in this entry can be modified when the
status of this entry is active(1)."
::= { pimStaticRPEntry 8 }
pimStaticRPStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this row. Rows having the value
'permanent' need not allow write-access to any columnar
objects in the row."
DEFVAL { nonVolatile }
::= { pimStaticRPEntry 9 }
-- -- The PIM Anycast-RP Set Table --
pimAnycastRPSetTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimAnycastRPSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to manage Anycast-RP via PIM Register
messages, as opposed to via other protocols such as MSDP
(Multicast Source Discovery Protocol).
Entries must be configured in this table if and only if the
local router is a member of one or more Anycast-RP sets,
that is, one or more Anycast-RP addresses are assigned to
the local router. Note that if using static RP
configuration, this is in addition to, not instead of, the
pimStaticRPTable entries that must be configured for the
Anycast-RPs.
The set of rows with the same values of both
pimAnycastRPSetAddressType and pimAnycastRPSetAnycastAddress
corresponds to the Anycast-RP set for that Anycast-RP
address.
When an Anycast-RP set configuration is active, one entry
per pimAnycastRPSetAnycastAddress corresponds to the local
router. The local router is identified by the
pimAnycastRpSetLocalRouter object. That entry determines
the source address used by the local router when forwarding
PIM Register messages within the Anycast-RP set."
REFERENCE "RFC 4610, RFC 3618"
::= { pim 12 }
pimAnycastRPSetEntry OBJECT-TYPE
SYNTAX PimAnycastRPSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry corresponds to a single router within a particular
Anycast-RP set. This entry is preserved on agent restart."
INDEX { pimAnycastRPSetAddressType,
pimAnycastRPSetAnycastAddress,
pimAnycastRPSetRouterAddress }
::= { pimAnycastRPSetTable 1 }
PimAnycastRPSetEntry ::= SEQUENCE {
pimAnycastRPSetAddressType InetAddressType, pimAnycastRPSetAnycastAddress InetAddress, pimAnycastRPSetRouterAddress InetAddress, pimAnycastRPSetLocalRouter TruthValue, pimAnycastRPSetRowStatus RowStatus, pimAnycastRPSetStorageType StorageType
}
pimAnycastRPSetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of the Anycast-RP address and router
address."
::= { pimAnycastRPSetEntry 1 }
pimAnycastRPSetAnycastAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Anycast-RP address. The InetAddressType is given by
the pimAnycastRPSetAddressType object."
::= { pimAnycastRPSetEntry 2 }
pimAnycastRPSetRouterAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address of a router that is a member of the Anycast-RP
set. The InetAddressType is given by the
pimAnycastRPSetAddressType object.
This address differs from pimAnycastRPSetAnycastAddress.
Equal values for these two addresses in a single entry are
not permitted. That would cause a Register loop."
::= { pimAnycastRPSetEntry 3 }
pimAnycastRPSetLocalRouter OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether this entry corresponds to the local router."
::= { pimAnycastRPSetEntry 4 }
pimAnycastRPSetRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row, by which rows in this table can
be created and destroyed.
This status object can be set to active(1) without setting
any other columnar objects in this entry.
All writeable objects in this entry can be modified when the
status of this entry is active(1)."
::= { pimAnycastRPSetEntry 5 }
pimAnycastRPSetStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this row. Rows having the value
'permanent' need not allow write-access to any columnar
objects in the row."
DEFVAL { nonVolatile }
::= { pimAnycastRPSetEntry 6 }
-- -- The PIM Group Mapping Table --
pimGroupMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimGroupMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing mappings from multicast
group prefixes to the PIM mode and RP address to use for
groups within that group prefix.
Rows in this table are created for a variety of reasons,
indicated by the value of the pimGroupMappingOrigin object.
- Rows with a pimGroupMappingOrigin value of 'fixed' are
created automatically by the router at startup, to
correspond to the well-defined prefixes of link-local and
unroutable group addresses. These rows are never
destroyed.
- Rows with a pimGroupMappingOrigin value of 'embedded' are
created by the router to correspond to group prefixes
that are to be treated as being in Embedded-RP format.
- Rows with a pimGroupMappingOrigin value of 'configRp' are
created and destroyed as a result of rows in the
pimStaticRPTable being created and destroyed.
- Rows with a pimGroupMappingOrigin value of 'configSsm'
are created and destroyed as a result of configuration of
SSM address ranges to the local router.
- Rows with a pimGroupMappingOrigin value of 'bsr' are
created as a result of running the PIM Bootstrap Router
(BSR) mechanism. If the local router is not the elected
BSR, these rows are created to correspond to group
prefixes in the PIM Bootstrap messages received from the
elected BSR. If the local router is the elected BSR,
these rows are created to correspond to group prefixes in
the PIM Bootstrap messages that the local router sends.
In either case, these rows are destroyed when the group
prefixes are timed out by the BSR mechanism.
- Rows with a pimGroupMappingOrigin value of 'other' are
created and destroyed according to some other mechanism
not specified here.
Given the collection of rows in this table at any point in
time, the PIM mode and RP address to use for a particular
group is determined using the following algorithm.
1. From the set of all rows, the subset whose group prefix
contains the group in question are selected.
2. If there are no such rows, then the group mapping is
undefined.
3. If there are multiple selected rows, and a subset is
defined by pimStaticRPTable (pimGroupMappingOrigin value
of 'configRp') with pimStaticRPOverrideDynamic set to
TRUE, then this subset is selected.
4. From the selected subset of rows, the subset that have
the greatest value of pimGroupMappingGrpPrefixLength are
selected.
5. If there are still multiple selected rows, the subset
that has the highest precedence (the lowest numerical
value for pimGroupMappingPrecedence) is selected.
6. If there are still multiple selected rows, the row
selected is implementation dependent; the implementation
might or might not apply the PIM hash function to select
the row.
7. The group mode to use is given by the value of
pimGroupMappingPimMode from the single selected row; the
RP to use is given by the value of
pimGroupMappingRPAddress, unless pimGroupMappingOrigin is
'embedded', in which case, the RP is extracted from the
group address in question."
REFERENCE "RFC 4601 section 3.7, RFC 3956, and RFC 4610"
::= { pim 13 }
pimGroupMappingEntry OBJECT-TYPE
SYNTAX PimGroupMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimGroupMappingTable."
INDEX { pimGroupMappingOrigin,
pimGroupMappingAddressType,
pimGroupMappingGrpAddress,
pimGroupMappingGrpPrefixLength,
pimGroupMappingRPAddressType,
pimGroupMappingRPAddress }
::= { pimGroupMappingTable 1 }
PimGroupMappingEntry ::= SEQUENCE {
pimGroupMappingOrigin PimGroupMappingOriginType, pimGroupMappingAddressType InetAddressType, pimGroupMappingGrpAddress InetAddress, pimGroupMappingGrpPrefixLength InetAddressPrefixLength, pimGroupMappingRPAddressType InetAddressType, pimGroupMappingRPAddress InetAddress, pimGroupMappingPimMode PimMode, pimGroupMappingPrecedence Unsigned32
}
pimGroupMappingOrigin OBJECT-TYPE
SYNTAX PimGroupMappingOriginType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mechanism by which this group mapping was learned."
::= { pimGroupMappingEntry 1 }
pimGroupMappingAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of the IP multicast group prefix."
::= { pimGroupMappingEntry 2 }
pimGroupMappingGrpAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP multicast group address that, when combined with
pimGroupMappingGrpPrefixLength, gives the group prefix for
this mapping. The InetAddressType is given by the
pimGroupMappingAddressType object.
This address object is only significant up to
pimGroupMappingGrpPrefixLength bits. The remainder of the
address bits are zero. This is especially important for
this index field, which is part of the index of this entry.
Any non-zero bits would signify an entirely different
entry."
::= { pimGroupMappingEntry 3 }
pimGroupMappingGrpPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength (4..128)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group prefix length that, when combined
with pimGroupMappingGrpAddress, gives the group prefix for
this mapping. The InetAddressType is given by the
pimGroupMappingAddressType object. If
pimGroupMappingAddressType is 'ipv4' or 'ipv4z', this
object must be in the range 4..32. If
pimGroupMappingAddressType is 'ipv6' or 'ipv6z', this object
must be in the range 8..128."
::= { pimGroupMappingEntry 4 }
pimGroupMappingRPAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of the RP to be used for groups within
this group prefix, or unknown(0) if no RP is to be used or
if the RP address is unknown. This object must be
unknown(0) if pimGroupMappingPimMode is ssm(2), or if
pimGroupMappingOrigin is embedded(6)."
::= { pimGroupMappingEntry 5 }
pimGroupMappingRPAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (0|4|8|16|20))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the RP to be used for groups within this
group prefix. The InetAddressType is given by the
pimGroupMappingRPAddressType object."
::= { pimGroupMappingEntry 6 }
pimGroupMappingPimMode OBJECT-TYPE
SYNTAX PimMode
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The PIM mode to be used for groups in this group prefix."
::= { pimGroupMappingEntry 7 }
pimGroupMappingPrecedence OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The precedence of this row, used in the algorithm that
determines which row applies to a given group address
(described above). Numerically higher values for this
object indicate lower precedences, with the value zero
denoting the highest precedence.
The absolute values of this object have a significance only
on the local router and do not need to be coordinated with
other routers."
::= { pimGroupMappingEntry 8 }
-- -- PIM Notifications --
pimNeighborLoss NOTIFICATION-TYPE
OBJECTS { pimNeighborUpTime }
STATUS current
DESCRIPTION
"A pimNeighborLoss notification signifies the loss of an
adjacency with a neighbor. This notification should be
generated when the neighbor timer expires, and the router
has no other neighbors on the same interface with the same
IP version and a lower IP address than itself.
This notification is generated whenever the counter
pimNeighborLossCount is incremented, subject
to the rate limit specified by
pimNeighborLossNotificationPeriod."
REFERENCE "RFC 4601 section 4.3.2"
::= { pimNotifications 1 }
pimInvalidRegister NOTIFICATION-TYPE
OBJECTS { pimGroupMappingPimMode,
pimInvalidRegisterAddressType,
pimInvalidRegisterOrigin,
pimInvalidRegisterGroup,
pimInvalidRegisterRp
}
STATUS current
DESCRIPTION
"A pimInvalidRegister notification signifies that an invalid
PIM Register message was received by this device.
This notification is generated whenever the counter
pimInvalidRegisterMsgsRcvd is incremented, subject to the
rate limit specified by
pimInvalidRegisterNotificationPeriod."
REFERENCE "RFC 4601 section 4.4.2"
::= { pimNotifications 2 }
pimInvalidJoinPrune NOTIFICATION-TYPE
OBJECTS { pimGroupMappingPimMode,
pimInvalidJoinPruneAddressType,
pimInvalidJoinPruneOrigin,
pimInvalidJoinPruneGroup,
pimInvalidJoinPruneRp,
pimNeighborUpTime
}
STATUS current
DESCRIPTION
"A pimInvalidJoinPrune notification signifies that an
invalid PIM Join/Prune message was received by this device.
This notification is generated whenever the counter
pimInvalidJoinPruneMsgsRcvd is incremented, subject to the
rate limit specified by
pimInvalidJoinPruneNotificationPeriod."
REFERENCE "RFC 4601 section 4.5.2" ::= { pimNotifications 3 }
pimRPMappingChange NOTIFICATION-TYPE
OBJECTS { pimGroupMappingPimMode,
pimGroupMappingPrecedence
}
STATUS current
DESCRIPTION
"A pimRPMappingChange notification signifies a change to the
active RP mapping on this device.
This notification is generated whenever the counter
pimRPMappingChangeCount is incremented, subject to the
rate limit specified by
pimRPMappingChangeNotificationPeriod."
::= { pimNotifications 4 }
pimInterfaceElection NOTIFICATION-TYPE
OBJECTS { pimInterfaceAddressType,
pimInterfaceAddress }
STATUS current
DESCRIPTION
"A pimInterfaceElection notification signifies that a new DR
or DF has been elected on a network.
This notification is generated whenever the counter
pimInterfaceElectionWinCount is incremented, subject to the
rate limit specified by
pimInterfaceElectionNotificationPeriod."
REFERENCE "RFC 4601 section 4.3.2 and RFC 5015 section 3.5.2"
::= { pimNotifications 5 }
-- -- Conformance Information --
pimMIBConformance OBJECT IDENTIFIER ::= { pimStdMIB 2 } pimMIBCompliances OBJECT IDENTIFIER ::= { pimMIBConformance 1 } pimMIBGroups OBJECT IDENTIFIER ::= { pimMIBConformance 2 }
-- -- Compliance Statements --
pimMIBComplianceAsm MODULE-COMPLIANCE
STATUS current DESCRIPTION
"The compliance statement for routers which are running
PIM-SM (Sparse Mode)."
MODULE -- this module
MANDATORY-GROUPS { pimTopologyGroup,
pimSsmGroup,
pimRPConfigGroup,
pimSmGroup }
GROUP pimNotificationGroup
DESCRIPTION
"This group is optional."
GROUP pimTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP pimRouterStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP pimAnycastRpGroup
DESCRIPTION
"This group is optional."
GROUP pimStaticRPPrecedenceGroup
DESCRIPTION
"This group is optional."
GROUP pimNetMgmtNotificationObjects
DESCRIPTION
"This group is optional."
GROUP pimNetMgmtNotificationGroup
DESCRIPTION
"This group is optional."
GROUP pimDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP pimDeviceStorageGroup
DESCRIPTION
"This group is optional."
::= { pimMIBCompliances 1 }
pimMIBComplianceBidir MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for routers which are running
Bidir-PIM."
MODULE -- this module
MANDATORY-GROUPS { pimTopologyGroup,
pimRPConfigGroup,
pimSmGroup,
pimBidirGroup }
GROUP pimNotificationGroup
DESCRIPTION
"This group is optional."
GROUP pimTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP pimRouterStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP pimAnycastRpGroup
DESCRIPTION
"This group is optional."
GROUP pimStaticRPPrecedenceGroup
DESCRIPTION
"This group is optional."
GROUP pimNetMgmtNotificationObjects
DESCRIPTION
"This group is optional."
GROUP pimNetMgmtNotificationGroup
DESCRIPTION
"This group is optional."
GROUP pimDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP pimDeviceStorageGroup
DESCRIPTION
"This group is optional."
::= { pimMIBCompliances 2 }
pimMIBComplianceSsm MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for routers which are running
PIM SSM (Source Specific Multicast)."
MODULE -- this module
MANDATORY-GROUPS { pimTopologyGroup,
pimSsmGroup }
GROUP pimNotificationGroup
DESCRIPTION
"This group is optional."
GROUP pimTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP pimRouterStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP pimNetMgmtNotificationObjects
DESCRIPTION
"This group is optional."
GROUP pimNetMgmtNotificationGroup
DESCRIPTION
"This group is optional."
GROUP pimDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP pimDeviceStorageGroup
DESCRIPTION
"This group is optional."
::= { pimMIBCompliances 3 }
pimMIBComplianceDm MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for routers which are running
PIM-DM (Dense Mode)."
MODULE -- this module
MANDATORY-GROUPS { pimTopologyGroup,
pimSsmGroup,
pimRPConfigGroup,
pimSmGroup,
pimDmGroup }
GROUP pimNotificationGroup
DESCRIPTION
"This group is optional."
GROUP pimTuningParametersGroup
DESCRIPTION
"This group is optional."
GROUP pimRouterStatisticsGroup
DESCRIPTION
"This group is optional."
GROUP pimAnycastRpGroup
DESCRIPTION
"This group is optional."
GROUP pimStaticRPPrecedenceGroup
DESCRIPTION
"This group is optional."
GROUP pimNetMgmtNotificationObjects
DESCRIPTION
"This group is optional."
GROUP pimNetMgmtNotificationGroup
DESCRIPTION
"This group is optional."
GROUP pimDiagnosticsGroup
DESCRIPTION
"This group is optional."
GROUP pimDeviceStorageGroup
DESCRIPTION
"This group is optional."
::= { pimMIBCompliances 4 }
-- -- Units of Conformance --
pimTopologyGroup OBJECT-GROUP
OBJECTS { pimInterfaceAddressType,
pimInterfaceAddress,
pimInterfaceGenerationIDValue,
pimInterfaceDR,
pimInterfaceDRPriorityEnabled,
pimInterfaceHelloHoldtime,
pimInterfaceJoinPruneHoldtime,
pimInterfaceLanDelayEnabled,
pimInterfaceEffectPropagDelay,
pimInterfaceEffectOverrideIvl,
pimInterfaceSuppressionEnabled,
pimInterfaceBidirCapable,
pimNeighborGenerationIDPresent,
pimNeighborGenerationIDValue,
pimNeighborUpTime,
pimNeighborExpiryTime,
pimNeighborDRPriorityPresent,
pimNeighborDRPriority,
pimNeighborLanPruneDelayPresent,
pimNeighborTBit,
pimNeighborPropagationDelay,
pimNeighborOverrideInterval,
pimNeighborBidirCapable,
pimNbrSecAddress
}
STATUS current
DESCRIPTION
"A collection of read-only objects used to report local PIM
topology."
::= { pimMIBGroups 1 }
pimNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS { pimNeighborLoss }
STATUS current
DESCRIPTION
"A collection of notifications for signaling important PIM
events."
::= { pimMIBGroups 2 }
pimTuningParametersGroup OBJECT-GROUP
OBJECTS { pimKeepalivePeriod,
pimRegisterSuppressionTime,
pimInterfaceDRPriority,
pimInterfaceHelloInterval,
pimInterfaceTrigHelloInterval,
pimInterfaceJoinPruneInterval,
pimInterfacePropagationDelay,
pimInterfaceOverrideInterval,
pimInterfaceDomainBorder,
pimInterfaceStubInterface,
pimInterfaceStatus,
pimInterfaceStorageType
}
STATUS current
DESCRIPTION
"A collection of writeable objects used to configure PIM
behavior and to tune performance."
::= { pimMIBGroups 3 }
pimRouterStatisticsGroup OBJECT-GROUP
OBJECTS { pimStarGEntries,
pimStarGIEntries,
pimSGEntries,
pimSGIEntries,
pimSGRptEntries,
pimSGRptIEntries
}
STATUS current
DESCRIPTION
"A collection of statistics global to the PIM router."
::= { pimMIBGroups 4 }
pimSsmGroup OBJECT-GROUP
OBJECTS { pimSGUpTime,
pimSGPimMode,
pimSGUpstreamJoinState,
pimSGUpstreamJoinTimer,
pimSGUpstreamNeighbor,
pimSGRPFIfIndex,
pimSGRPFNextHopType,
pimSGRPFNextHop,
pimSGRPFRouteProtocol,
pimSGRPFRouteAddress,
pimSGRPFRoutePrefixLength,
pimSGRPFRouteMetricPref,
pimSGRPFRouteMetric,
pimSGSPTBit,
pimSGKeepaliveTimer,
pimSGDRRegisterState,
pimSGDRRegisterStopTimer,
pimSGRPRegisterPMBRAddressType,
pimSGRPRegisterPMBRAddress,
pimSGIUpTime,
pimSGILocalMembership,
pimSGIJoinPruneState,
pimSGIPrunePendingTimer,
pimSGIJoinExpiryTimer,
pimSGIAssertState,
pimSGIAssertTimer,
pimSGIAssertWinnerAddressType,
pimSGIAssertWinnerAddress,
pimSGIAssertWinnerMetricPref,
pimSGIAssertWinnerMetric
}
STATUS current
DESCRIPTION
"A collection of objects to support management of PIM
routers running the PIM SSM (Source Specific Multicast)
protocol, in PIM mode SM (Sparse Mode)."
::= { pimMIBGroups 5 }
pimRPConfigGroup OBJECT-GROUP
OBJECTS { pimStaticRPRPAddress,
pimStaticRPPimMode,
pimStaticRPOverrideDynamic,
pimStaticRPRowStatus,
pimStaticRPStorageType,
pimGroupMappingPimMode,
pimGroupMappingPrecedence
}
STATUS current
DESCRIPTION
"A collection of objects to support configuration of RPs
(Rendezvous Points) and Group Mappings."
::= { pimMIBGroups 6 }
pimSmGroup OBJECT-GROUP
OBJECTS { pimStarGUpTime,
pimStarGPimMode,
pimStarGRPAddressType,
pimStarGRPAddress,
pimStarGPimModeOrigin,
pimStarGRPIsLocal,
pimStarGUpstreamJoinState,
pimStarGUpstreamJoinTimer,
pimStarGUpstreamNeighborType,
pimStarGUpstreamNeighbor,
pimStarGRPFIfIndex,
pimStarGRPFNextHopType,
pimStarGRPFNextHop,
pimStarGRPFRouteProtocol,
pimStarGRPFRouteAddress,
pimStarGRPFRoutePrefixLength,
pimStarGRPFRouteMetricPref,
pimStarGRPFRouteMetric,
pimStarGIUpTime,
pimStarGILocalMembership,
pimStarGIJoinPruneState,
pimStarGIPrunePendingTimer,
pimStarGIJoinExpiryTimer,
pimStarGIAssertState,
pimStarGIAssertTimer,
pimStarGIAssertWinnerAddressType,
pimStarGIAssertWinnerAddress,
pimStarGIAssertWinnerMetricPref,
pimStarGIAssertWinnerMetric,
pimSGRptUpTime,
pimSGRptUpstreamPruneState,
pimSGRptUpstreamOverrideTimer,
pimSGRptIUpTime,
pimSGRptILocalMembership,
pimSGRptIJoinPruneState,
pimSGRptIPrunePendingTimer,
pimSGRptIPruneExpiryTimer
}
STATUS current
DESCRIPTION
"A collection of objects to support management of PIM
routers running PIM-SM (Sparse Mode). The groups
pimSsmGroup and pimRPConfigGroup are also required."
::= { pimMIBGroups 7 }
pimBidirGroup OBJECT-GROUP
OBJECTS { pimInterfaceDFElectionRobustness,
pimBidirDFElectionWinnerAddressType,
pimBidirDFElectionWinnerAddress,
pimBidirDFElectionWinnerUpTime,
pimBidirDFElectionWinnerMetricPref,
pimBidirDFElectionWinnerMetric,
pimBidirDFElectionState,
pimBidirDFElectionStateTimer
}
STATUS current
DESCRIPTION
"A collection of objects to support management of PIM
routers running BIDIR mode. The groups pimSsmGroup,
pimSmGroup and pimRPConfigGroup are also required."
::= { pimMIBGroups 8 }
pimAnycastRpGroup OBJECT-GROUP
OBJECTS { pimAnycastRPSetLocalRouter,
pimAnycastRPSetRowStatus,
pimAnycastRPSetStorageType
}
STATUS current
DESCRIPTION
"A collection of objects to support management of the PIM
Anycast-RP mechanism."
::= { pimMIBGroups 9 }
pimStaticRPPrecedenceGroup OBJECT-GROUP
OBJECTS { pimStaticRPPrecedence }
STATUS current
DESCRIPTION
"A collection of objects to allow fine control of
interactions between static RP configuration and
dynamically acquired group to RP mappings."
::= { pimMIBGroups 10 }
pimNetMgmtNotificationObjects OBJECT-GROUP
OBJECTS { pimInvalidRegisterNotificationPeriod,
pimInvalidRegisterMsgsRcvd,
pimInvalidRegisterAddressType,
pimInvalidRegisterOrigin,
pimInvalidRegisterGroup,
pimInvalidRegisterRp,
pimInvalidJoinPruneNotificationPeriod,
pimInvalidJoinPruneMsgsRcvd,
pimInvalidJoinPruneAddressType,
pimInvalidJoinPruneOrigin,
pimInvalidJoinPruneGroup,
pimInvalidJoinPruneRp,
pimRPMappingNotificationPeriod,
pimRPMappingChangeCount,
pimInterfaceElectionNotificationPeriod,
pimInterfaceElectionWinCount
}
STATUS current
DESCRIPTION
"A collection of objects to support notification of PIM
network management events."
::= { pimMIBGroups 11 }
pimNetMgmtNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS { pimInvalidRegister,
pimInvalidJoinPrune,
pimRPMappingChange,
pimInterfaceElection
}
STATUS current
DESCRIPTION
"A collection of notifications for signaling PIM network
management events."
::= { pimMIBGroups 12 }
pimDiagnosticsGroup OBJECT-GROUP
OBJECTS { pimInAsserts,
pimOutAsserts,
pimLastAssertInterface,
pimLastAssertGroupAddressType,
pimLastAssertGroupAddress,
pimLastAssertSourceAddressType,
pimLastAssertSourceAddress,
pimNeighborLossNotificationPeriod,
pimNeighborLossCount
}
STATUS current
DESCRIPTION
"Objects providing additional diagnostics related to a PIM
router."
::= { pimMIBGroups 13 }
pimDmGroup OBJECT-GROUP
OBJECTS {
pimRefreshInterval,
pimInterfacePruneLimitInterval,
pimInterfaceGraftRetryInterval,
pimInterfaceSRPriorityEnabled,
pimNeighborSRCapable,
pimSGUpstreamPruneState,
pimSGUpstreamPruneLimitTimer,
pimSGOriginatorState,
pimSGSourceActiveTimer,
pimSGStateRefreshTimer
}
STATUS current
DESCRIPTION
"A collection of objects required for management of PIM
Dense Mode (PIM-DM) function. The groups pimSsmGroup and
pimSmGroup are also required."
REFERENCE "RFC 3973"
::= { pimMIBGroups 14 }
pimDeviceStorageGroup OBJECT-GROUP
OBJECTS { pimDeviceConfigStorageType
}
STATUS current
DESCRIPTION
"An object that specifies the volatility of global PIM
configuration settings on this device."
::= { pimMIBGroups 15 }
END
Security Considerations
There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability:
The following tables and objects could be employed to modify multicast routing behavior in a way that prevents, disrupts, or subverts services provided by the network, including (but not limited to) multicast data traffic delivery. For example, attacks can be envisaged that would pass nominated multicast data streams through a nominated location, without the sources or listeners becoming aware of this subversion.
pimKeepalivePeriod pimRegisterSuppressionTime pimNeighborLossNotificationPeriod pimInvalidRegisterNotificationPeriod pimInvalidJoinPruneNotificationPeriod pimRPMappingNotificationPeriod pimInterfaceElectionNotificationPeriod pimRefreshInterval pimInterfaceTable pimInterfaceEntry pimInterfaceIfIndex pimInterfaceIPVersion pimInterfaceHelloInterval pimInterfaceTrigHelloInterval pimInterfaceJoinPruneInterval pimInterfaceDFElectionRobustness pimInterfaceHelloHoldtime pimInterfaceJoinPruneHoldtime pimInterfacePropagationDelay pimInterfaceOverrideInterval pimInterfaceDRPriority pimInterfaceDomainBorder pimInterfaceStatus pimInterfaceStubInterface pimInterfacePruneLimitInterval pimStaticRPTable pimStaticRPEntry pimStaticRPAddressType pimStaticRPGrpAddress pimStaticRPGrpPrefixLength pimStaticRPRPAddress pimStaticRPPimMode pimStaticRPOverrideDynamic pimStaticRPRowStatus pimStaticRPPrecedence pimAnycastRPSetTable pimAnycastRPSetEntry pimAnycastRPSetAddressType pimAnycastRPSetAnycastAddress pimAnycastRPSetRouterAddress
Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability:
The following tables and objects could be employed to determine the topology, disposition, and composition of the network. This information may be commercially sensitive, and may also be used in preparation for attacks, including any of the attacks described above.
The following tables and objects may also be used to determine whether multicast data is flowing in the network, or has flowed recently. They may also be used to determine the network location of senders and recipients. An attacker can apply 'traffic analysis' to this data. In some cases, the information revealed by traffic analyses can be as damaging as full knowledge of the data being transported.
pimKeepalivePeriod pimRegisterSuppressionTime pimStarGEntries pimStarGIEntries pimSGEntries pimSGIEntries pimSGRptEntries pimSGRptIEntries pimOutAsserts pimInAsserts pimLastAssertInterface pimLastAssertGroupAddressType pimLastAssertGroupAddress pimLastAssertSourceAddressType pimLastAssertSourceAddress pimNeighborLossNotificationPeriod pimNeighborLossCount pimInvalidRegisterNotificationPeriod pimInvalidRegisterMsgsRcvd pimInvalidRegisterAddressType pimInvalidRegisterOrigin pimInvalidRegisterGroup pimInvalidRegisterRp pimInvalidJoinPruneNotificationPeriod pimInvalidJoinPruneMsgsRcvd pimInvalidJoinPruneAddressType pimInvalidJoinPruneOrigin pimInvalidJoinPruneGroup pimInvalidJoinPruneRp pimRPMappingNotificationPeriod pimRPMappingChangeCount pimInterfaceElectionNotificationPeriod pimInterfaceElectionWinCount pimRefreshInterval pimInterfaceTable pimInterfaceEntry pimInterfaceIfIndex pimInterfaceIPVersion pimInterfaceAddressType pimInterfaceAddress pimInterfaceDR pimInterfaceHelloInterval pimInterfaceTrigHelloInterval pimInterfaceJoinPruneInterval pimInterfaceDFElectionRobustness pimInterfaceHelloHoldtime pimInterfaceJoinPruneHoldtime pimInterfacePropagationDelay pimInterfaceOverrideInterval pimInterfaceGenerationIDValue pimInterfaceDRPriority pimInterfaceLanDelayEnabled pimInterfaceEffectPropagDelay pimInterfaceEffectOverrideIvl pimInterfaceSuppressionEnabled pimInterfaceBidirCapable pimInterfaceDRPriorityEnabled pimInterfaceDomainBorder pimInterfaceStatus pimInterfaceStubInterface
pimInterfacePruneLimitInterval pimInterfaceSRPriorityEnabled pimNeighborTable pimNeighborEntry pimNeighborIfIndex pimNeighborAddressType pimNeighborAddress pimNeighborUpTime pimNeighborExpiryTime pimNeighborLanPruneDelayPresent pimNeighborPropagationDelay pimNeighborOverrideInterval pimNeighborTBit pimNeighborGenerationIDPresent pimNeighborGenerationIDValue pimNeighborBidirCapable pimNeighborDRPriorityPresent pimNeighborDRPriority pimNeighborSRCapable pimNbrSecAddressTable pimNbrSecAddressEntry pimNbrSecAddressIfIndex pimNbrSecAddressType pimNbrSecAddressPrimary pimNbrSecAddress pimStarGTable pimStarGEntry pimStarGAddressType pimStarGGrpAddress pimStarGUpTime pimStarGPimMode pimStarGRPAddressType pimStarGRPAddress pimStarGPimModeOrigin pimStarGRPIsLocal pimStarGUpstreamJoinState pimStarGUpstreamJoinTimer pimStarGUpstreamNeighborType pimStarGUpstreamNeighbor pimStarGRPFIfIndex pimStarGRPFNextHopType pimStarGRPFNextHop pimStarGRPFRouteProtocol pimStarGRPFRouteAddress pimStarGRPFRoutePrefixLength pimStarGRPFRouteMetricPref pimStarGRPFRouteMetric pimStarGITable pimStarGIEntry pimStarGIIfIndex pimStarGIUpTime pimStarGILocalMembership pimStarGIJoinPruneState pimStarGIPrunePendingTimer pimStarGIJoinExpiryTimer pimStarGIAssertState pimStarGIAssertTimer pimStarGIAssertWinnerAddressType pimStarGIAssertWinnerAddress pimStarGIAssertWinnerMetricPref pimStarGIAssertWinnerMetric pimSGTable pimSGEntry pimSGAddressType pimSGGrpAddress pimSGSrcAddress pimSGUpTime pimSGPimMode pimSGUpstreamJoinState pimSGUpstreamJoinTimer pimSGUpstreamNeighbor pimSGRPFIfIndex pimSGRPFNextHopType pimSGRPFNextHop pimSGRPFRouteProtocol pimSGRPFRouteAddress pimSGRPFRoutePrefixLength pimSGRPFRouteMetricPref pimSGRPFRouteMetric pimSGSPTBit pimSGKeepaliveTimer pimSGDRRegisterState pimSGDRRegisterStopTimer pimSGRPRegisterPMBRAddressType pimSGRPRegisterPMBRAddress pimSGUpstreamPruneState pimSGUpstreamPruneLimitTimer pimSGOriginatorState pimSGSourceActiveTimer pimSGStateRefreshTimer pimSGITable pimSGIEntry pimSGIIfIndex pimSGIUpTime pimSGILocalMembership pimSGIJoinPruneState pimSGIPrunePendingTimer pimSGIJoinExpiryTimer pimSGIAssertState pimSGIAssertTimer pimSGIAssertWinnerAddressType pimSGIAssertWinnerAddress pimSGIAssertWinnerMetricPref pimSGIAssertWinnerMetric pimSGRptTable pimSGRptEntry pimSGRptSrcAddress pimSGRptUpTime pimSGRptUpstreamPruneState pimSGRptUpstreamOverrideTimer pimSGRptITable pimSGRptIEntry pimSGRptIIfIndex pimSGRptIUpTime pimSGRptILocalMembership pimSGRptIJoinPruneState pimSGRptIPrunePendingTimer pimSGRptIPruneExpiryTimer pimBidirDFElectionTable pimBidirDFElectionEntry pimBidirDFElectionAddressType pimBidirDFElectionRPAddress pimBidirDFElectionIfIndex pimBidirDFElectionWinnerAddressType pimBidirDFElectionWinnerAddress pimBidirDFElectionWinnerUpTime
pimBidirDFElectionWinnerMetricPref pimBidirDFElectionWinnerMetric pimBidirDFElectionState pimBidirDFElectionStateTimer pimStaticRPTable pimStaticRPEntry pimStaticRPAddressType pimStaticRPGrpAddress pimStaticRPGrpPrefixLength pimStaticRPRPAddress pimStaticRPPimMode pimStaticRPOverrideDynamic pimStaticRPRowStatus pimStaticRPPrecedence pimAnycastRPSetTable pimAnycastRPSetEntry pimAnycastRPSetAddressType pimAnycastRPSetAnycastAddress pimAnycastRPSetRouterAddress pimAnycastRPSetRowStatus pimAnycastRPSetLocalRouter pimGroupMappingTable pimGroupMappingEntry pimGroupMappingOrigin pimGroupMappingAddressType pimGroupMappingGrpAddress pimGroupMappingGrpPrefixLength pimGroupMappingRPAddress pimGroupMappingPimMode pimGroupMappingPrecedence
There is also a specific danger arising from the notification pimInvalidRegister. This is originated by devices that receive an incorrect unicast-encapsulated multicast data packet, which poses a clear danger of propagating a DoS (Denial of Service) attack from the data or control plane to the network management plane. The following steps are taken to guard against this.
1. The notification is disabled by default. The writeable field
pimInvalidRegisterNotificationPeriod must be set in order to enable it.
2. The syntax of pimInvalidRegisterNotificationPeriod prevents any
given device from originating the notification more frequently than once every 10 seconds.
3. The counter pimInvalidRegisterMsgsRcvd provides equivalent
function to the notification. Management applications are encouraged to monitor this counter in preference to enabling the notification.
The same measures are taken in respect of pimInvalidJoinPrune, though as this notification can only arise as a result of unroutable control packets, the risk is not so acute.
SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.
It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see RFC3410, section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them.
IANA Considerations
PIM-STD-MIB is rooted under the mib-2 subtree. IANA has assigned { mib-2 157 } to the PIM-STD-MIB module specified in this document.
Acknowledgements
This MIB module is based on the original work in RFC 2934 RFC2934 by K. McCloghrie, D. Farinacci, D. Thaler, and W. Fenner and has been updated based on feedback from the IETF's Protocol Independent Multicast (PIM) Working Group.
Jonathan Nicholas was the editor of early versions of this document, and contributed the objects for management of PIM-DM.
References
Normative References
RFC2119 Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
RFC2578 McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578,
April 1999.
RFC2579 McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
STD 58, RFC 2579, April 1999.
RFC2580 McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999.
RFC2863 McCloghrie, K. and F. Kastenholz, "The Interfaces
Group MIB", RFC 2863, June 2000.
RFC3973 Adams, A., Nicholas, J., and W. Siadak, "Protocol
Independent Multicast - Dense Mode (PIM-DM): Protocol
Specification (Revised)", RFC 3973, January 2005.
RFC4001 Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwaelder, "Textual Conventions for Internet
Network Addresses", RFC 4001, February 2005.
RFC4601 Fenner, B., Handley, M., Holbrook, H., and I.
Kouvelas, "Protocol Independent Multicast - Sparse
Mode (PIM-SM): Protocol Specification (Revised)",
RFC 4601, August 2006.
RFC4610 Farinacci, D. and Y. Cai, "Anycast-RP Using Protocol
Independent Multicast (PIM)", RFC 4610, August 2006.
RFC5015 Handley, M., Kouvelas, I., Speakman, T., and L.
Vicisano, "Bidirectional Protocol Independent
Multicast (BIDIR-PIM)", RFC 5015, October 2007.
RFC5059 Bhaskar, N., Gall, A., Lingard, L., and S. Venaas,
"Bootstrap Router (BSR) Mechanism for PIM", RFC 5059, January 2008.
[RTPROTO] IANA, "IP Route Protocol MIB", September 2000, <http:/
/www.iana.org/assignments/ianaiprouteprotocol-mib>.
Informative References
[IPMCAST-MIB] McWalter, D., "IP Multicast MIB", Work in Progress,
August 2007.
RFC2932 McCloghrie, K., Farinacci, D., and D. Thaler, "IPv4
Multicast Routing MIB", RFC 2932, October 2000.
RFC2934 McCloghrie, K., Farinacci, D., Thaler, D., and B.
Fenner, "Protocol Independent Multicast MIB for IPv4",
RFC 2934, October 2000.
RFC3376 Cain, B., Deering, S., Kouvelas, I., Fenner, B., and
A. Thyagarajan, "Internet Group Management Protocol,
Version 3", RFC 3376, October 2002.
RFC3410 Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
RFC3569 Bhattacharyya, S., "An Overview of Source-Specific
Multicast (SSM)", RFC 3569, July 2003.
RFC3618 Fenner, B. and D. Meyer, "Multicast Source Discovery
Protocol (MSDP)", RFC 3618, October 2003.
RFC3810 Vida, R. and L. Costa, "Multicast Listener Discovery
Version 2 (MLDv2) for IPv6", RFC 3810, June 2004.
RFC3956 Savola, P. and B. Haberman, "Embedding the Rendezvous
Point (RP) Address in an IPv6 Multicast Address",
RFC 3956, November 2004.
Authors' Addresses
Raghava Sivaramu Cisco Systems 425 E. Tasman Drive San Jose, CA 95134 USA
EMail: [email protected]
James Lingard Arastra, Inc P.O. Box 10905 Palo Alto, CA 94303 USA
EMail: [email protected]
David McWalter Data Connection Ltd 100 Church Street Enfield EN2 6BQ United Kingdom
EMail: [email protected]
Bharat Joshi Infosys Technologies Ltd Electronic City Bangalore 560 100 India
EMail: [email protected]
Andrew Kessler Cisco Systems 425 E. Tasman Drive San Jose, CA 95134 USA
EMail: [email protected]
Full Copyright Statement
Copyright (C) The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights.
This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at [email protected].
