RFC6373

From RFC-Wiki

Internet Engineering Task Force (IETF) L. Andersson, Ed. Request for Comments: 6373 Ericsson Category: Informational L. Berger, Ed. ISSN: 2070-1721 LabN

                                                        L. Fang, Ed.
                                                               Cisco
                                                       N. Bitar, Ed.
                                                             Verizon
                                                        E. Gray, Ed.
                                                            Ericsson
                                                      September 2011
    MPLS Transport Profile (MPLS-TP) Control Plane Framework

Abstract

The MPLS Transport Profile (MPLS-TP) supports static provisioning of transport paths via a Network Management System (NMS) and dynamic provisioning of transport paths via a control plane. This document provides the framework for MPLS-TP dynamic provisioning and covers control-plane addressing, routing, path computation, signaling, traffic engineering, and path recovery. MPLS-TP uses GMPLS as the control plane for MPLS-TP Label Switched Paths (LSPs). MPLS-TP also uses the pseudowire (PW) control plane for pseudowires. Management- plane functions are out of scope of this document.

This document is a product of a joint Internet Engineering Task Force (IETF) / International Telecommunication Union Telecommunication Standardization Sector (ITU-T) effort to include an MPLS Transport Profile within the IETF MPLS and Pseudowire Emulation Edge-to-Edge (PWE3) architectures to support the capabilities and functionalities of a packet transport network as defined by the ITU-T.

Status of This Memo

This document is not an Internet Standards Track specification; it is published for informational purposes.

This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Not all documents approved by the IESG are a candidate for any level of Internet Standard; see Section 2 of RFC 5741.

Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc6373.

Copyright Notice

Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.

       4.1.10. Control-Plane Reference Points (E-NNI,
       4.4.1. MPLS-TE to MPLS-TP LSP Control-Plane Interworking ..37
       5.3.2. Support for Explicit Control of PW-to-LSP Binding ..45
       5.3.3. Support for Dynamic Transfer of PW
       5.3.4. Interoperable Support for PW/LSP Resource
       5.3.5. Support for PW Protection and PW OAM
       5.3.6. Client Layer and Cross-Provider Interfaces

Contents

Introduction

The Multiprotocol Label Switching Transport Profile (MPLS-TP) is defined as a joint effort between the International Telecommunication Union (ITU) and the IETF. The requirements for MPLS-TP are defined in the requirements document, see RFC5654. These requirements state that "A solution MUST be defined to support dynamic provisioning of MPLS-TP transport paths via a control plane". This document provides the framework for such dynamic provisioning. This document is a product of a joint Internet Engineering Task Force (IETF) / International Telecommunication Union Telecommunication Standardization Sector (ITU-T) effort to include an MPLS Transport Profile within the IETF MPLS and Pseudowire Emulation Edge-to-Edge (PWE3) architectures to support the capabilities and functions of a packet transport network as defined by the ITU-T.

Scope

This document covers the control-plane functions involved in establishing MPLS-TP Label Switched Paths (LSPs) and pseudowires (PWs). The control-plane requirements for MPLS-TP are defined in the MPLS-TP requirements document RFC5654. These requirements define the role of the control plane in MPLS-TP. In particular, Section 2.4 of RFC5654 and portions of the remainder of Section 2 of RFC5654 provide specific control-plane requirements.

The LSPs provided by MPLS-TP are used as a server layer for IP, MPLS, and PWs, as well as other tunneled MPLS-TP LSPs. The PWs are used to carry client signals other than IP or MPLS. The relationship between PWs and MPLS-TP LSPs is exactly the same as between PWs and MPLS LSPs in an MPLS Packet Switched Network (PSN). The PW encapsulation over MPLS-TP LSPs used in MPLS-TP networks is also the same as for PWs over MPLS in an MPLS network. MPLS-TP also defines protection and restoration (or, collectively, recovery) functions; see RFC5654 and RFC4427. The MPLS-TP control plane provides methods to establish, remove, and control MPLS-TP LSPs and PWs. This includes control of Operations, Administration, and Maintenance (OAM), data-plane, and recovery functions.

A general framework for MPLS-TP has been defined in RFC5921, and a survivability framework for MPLS-TP has been defined in RFC6372. These documents scope the approaches and protocols that are the foundation of MPLS-TP. Notably, Section 3.5 of RFC5921 scopes the IETF protocols that serve as the foundation of the MPLS-TP control plane. The PW control plane is based on the existing PW control plane (see RFC4447) and the PWE3 architecture (see RFC3985). The LSP control plane is based on GMPLS (see RFC3945), which is built on MPLS Traffic Engineering (TE) and its numerous extensions. RFC6372 focuses on the recovery functions that must be supported within MPLS-TP. It does not specify which control-plane mechanisms are to be used.

The remainder of this document discusses the impact of the MPLS-TP requirements on the GMPLS signaling and routing protocols that are used to control MPLS-TP LSPs, and on the control of PWs as specified in RFC4447, RFC6073, and [MS-PW-DYNAMIC].

Basic Approach

The basic approach taken in defining the MPLS-TP control-plane framework includes the following:

  1) MPLS technology as defined by the IETF is the foundation for
     the MPLS Transport Profile.
  2) The data plane for MPLS-TP is a standard MPLS data plane
     RFC3031 as profiled in RFC5960.
  3) MPLS PWs are used by MPLS-TP including the use of targeted
     Label Distribution Protocol (LDP) as the foundation for PW
     signaling RFC4447.  This also includes the use of Open
     Shortest Path First with Traffic Engineering (OSPF-TE),
     Intermediate System to Intermediate System (IS-IS) with Traffic
     Engineering (ISIS-TE), or Multiprotocol Border Gateway Protocol
     (MP-BGP) as they apply for Multi-Segment Pseudowire (MS-PW)
     routing.  However, the PW can be encapsulated over an MPLS-TP
     LSP (established using methods and procedures for MPLS-TP LSP
     establishment) in addition to the presently defined methods of
     carrying PWs over LSP-based PSNs.  That is, the MPLS-TP domain
     is a PSN from a PWE3 architecture perspective RFC3985.
  4) The MPLS-TP LSP control plane builds on the GMPLS control plane
     as defined by the IETF for transport LSPs.  The protocols
     within scope are Resource Reservation Protocol with Traffic
     Engineering (RSVP-TE) RFC3473, OSPF-TE RFC4203 RFC5392,
     and ISIS-TE RFC5307 RFC5316.  Automatically Switched
     Optical Network (ASON) signaling and routing requirements in
     the context of GMPLS can be found in RFC4139 and RFC4258.
  5) Existing IETF MPLS and GMPLS RFCs and evolving Working Group
     Internet-Drafts should be reused wherever possible.
  6) If needed, extensions for the MPLS-TP control plane should
     first be based on the existing and evolving IETF work, and
     secondly be based on work by other standard bodies only when
     IETF decides that the work is out of the IETF's scope.  New
     extensions may be defined otherwise.
  7) Extensions to the control plane may be required in order to
     fully automate functions related to MPLS-TP LSPs and PWs.
  8) Control-plane software upgrades to existing equipment are
     acceptable and expected.
  9) It is permissible for functions present in the GMPLS and PW
     control planes to not be used in MPLS-TP networks.
 10) One possible use of the control plane is to configure, enable,
     and generally control OAM functionality.  This will require
     extensions to existing control-plane specifications that will
     be usable in MPLS-TP as well as MPLS networks.
 11) The foundation for MPLS-TP control-plane requirements is
     primarily found in Section 2.4 of RFC5654 and relevant
     portions of the remainder of Section 2 of RFC5654.

Reference Model

The control-plane reference model is based on the general MPLS-TP reference model as defined in the MPLS-TP framework RFC5921 and further refined in RFC6215 on the MPLS-TP User-to-Network and Network-to-Network Interfaces (UNI and NNI, respectively). Per the MPLS-TP framework RFC5921, the MPLS-TP control plane is based on GMPLS with RSVP-TE for LSP signaling and targeted LDP for PW signaling. In both cases, OSPF-TE or ISIS-TE with GMPLS extensions is used for dynamic routing within an MPLS-TP domain.

Note that in this context, "targeted LDP" (or T-LDP) means LDP as defined in RFC 5036, using Targeted Hello messages. See Section 2.4.2 ("Extended Discovery Mechanism") of RFC5036. Use of the extended discovery mechanism is specified in Section 5 ("LDP") of RFC4447.

From a service perspective, MPLS-TP client services may be supported via both PWs and LSPs. PW client interfaces, or adaptations, are defined on an interface-technology basis, e.g., Ethernet over PW RFC4448. In the context of MPLS-TP LSP, the client interface is provided at the network layer and may be controlled via a GMPLS-based UNI, see RFC4208, or statically provisioned. As discussed in RFC5921 and RFC6215, MPLS-TP also presumes an NNI reference point.

The MPLS-TP end-to-end control-plane reference model is shown in Figure 1. The figure shows the control-plane protocols used by MPLS- TP, as well as the UNI and NNI reference points, in the case of a Single-Segment PW supported by an end-to-end LSP without any hierarchical LSPs. (The MS-PW case is not shown.) Each service provider node's participation in routing and signaling (both GMPLS RSVP-TE and PW LDP) is represented. Note that only the service end points participate in PW LDP signaling, while all service provider nodes participate in GMPLS TE LSP routing and signaling.

   |< ---- client signal (e.g., IP / MPLS / L2) -------- >|
     |< --------- SP1 ---------- >|< ------- SP2 ----- >|
       |< ---------- MPLS-TP End-to-End PW --------- >|
         |< -------- MPLS-TP End-to-End LSP ------ >|

+---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ |CE1|-|-|PE1|--|P1 |--|P2 |--|PE2|-|-|PEa|--|Pa |--|PEb|-|-|CE2| +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+

    UNI                          NNI                   UNI

GMPLS

TE-RTG,  |<-----|------|------|-------|------|----->|
& RSVP-TE

PW LDP |< ---------------------------------------- >|

Figure 1.  End-to-End MPLS-TP Control-Plane Reference Model
 Legend:
      CE:            Customer Edge
      Client signal: defined in MPLS-TP Requirements
      L2:            Any layer 2 signal that may be carried
                     over a PW, e.g., Ethernet
      NNI:           Network-to-Network Interface
      P:             Provider
      PE:            Provider Edge
      SP:            Service Provider
      TE-RTG:        GMPLS OSPF-TE or ISIS-TE
      UNI:           User-to-Network Interface
 Note: The MS-PW case is not shown.

Figure 2 adds three hierarchical LSP segments, labeled as "H-LSPs". These segments are present to support scaling, OAM, and Maintenance Entity Group End Points (MEPs), see RFC6371, within each provider domain and across the inter-provider NNI. (H-LSPs are used to implement Sub-Path Maintenance Elements (SPMEs) as defined in RFC5921.) The MEPs are used to collect performance information, support diagnostic and fault management functions, and support OAM triggered survivability schemes as discussed in RFC6372. Each H-LSP may be protected or restored using any of the schemes discussed in RFC6372. End-to-end monitoring is supported via MEPs at the end-to-end LSP and PW end points. Note that segment MEPs may be co- located with MIPs of the next higher-layer (e.g., end-to-end) LSPs. (The MS-PW case is not shown.)

   |< ------- client signal (e.g., IP / MPLS / L2) ----- >|
     |< -------- SP1 ----------- >|< ------- SP2 ----- >|
       |< ----------- MPLS-TP End-to-End PW -------- >|
         |< ------- MPLS-TP End-to-End LSP ------- >|
         |< -- H-LSP1 ---- >|<-H-LSP2->|<- H-LSP3 ->|

+---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ |CE1|-|-|PE1|--|P1 |--|P2 |--|PE2|-|-|PEa|--|Pa |--|PEb|-|-|CE2| +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+ +---+

    UNI                          NNI                   UNI

End2end |MEP|--------------------------------------|MEP| PW OAM

End2end |MEP|----------------|MIP|---|MIP|---------|MEP| LSP OAM

Segment |MEP|-|MIP|-|MIP|-|MEP|MEP|-|MEP|MEP|-|MIP|-|MEP| LSP OAM '''' ''''

H-LSP GMPLS

TE-RTG   |<-----|------|----->||<---->||<-----|----->|
&RSVP-TE (within an MPLS-TP network)

E2E GMPLS

TE-RTG   |< ------------------|--------|------------>|
&RSVP-TE

PW LDP |< ---------------------------------------- >|

 Figure 2.  MPLS-TP Control-Plane Reference Model with OAM
 Legend:
      CE:            Customer Edge
      Client signal: defined in MPLS-TP Requirements
      E2E:           End-to-End
      L2:            Any layer 2 signal that may be carried
                     over a PW, e.g., Ethernet
      H-LSP:         Hierarchical LSP
      MEP:           Maintenance Entity Group End Point
      MIP:           Maintenance Entity Group Intermediate Point
      NNI:           Network-to-Network Interface
      P:             Provider
      PE:            Provider Edge
      SP:            Service Provider
      TE-RTG:        GMPLS OSPF-TE or ISIS-TE
 Note: The MS-PW case is not shown.

While not shown in the figures above, the MPLS-TP control plane must support the addressing separation and independence between the data, control, and management planes. Address separation between the planes is already included in GMPLS. Such separation is also already included in LDP as LDP session end point addresses are never automatically associated with forwarding.

Control-Plane Requirements

The requirements for the MPLS-TP control plane are derived from the MPLS-TP requirements and framework documents, specifically RFC5654, RFC5921, RFC5860, RFC6371, and RFC6372. The requirements are summarized in this section, but do not replace those documents. If there are differences between this section and those documents, those documents shall be considered authoritative.

Primary Requirements

These requirements are based on Section 2 of RFC5654:

  1. Any new functionality that is defined to fulfill the
     requirements for MPLS-TP must be agreed within the IETF through
     the IETF consensus process as per RFC4929 and Section 1,
     paragraph 15 of RFC5654.
  2. The MPLS-TP control-plane design should as far as reasonably
     possible reuse existing MPLS standards (RFC5654, requirement
     2).
  3. The MPLS-TP control plane must be able to interoperate with
     existing IETF MPLS and PWE3 control planes where appropriate
     (RFC5654, requirement 3).
  4. The MPLS-TP control plane must be sufficiently well-defined to
     ensure that the interworking between equipment supplied by
     multiple vendors will be possible both within a single domain
     and between domains (RFC5654, requirement 4).
  5. The MPLS-TP control plane must support a connection-oriented
     packet switching model with traffic engineering capabilities
     that allow deterministic control of the use of network
     resources (RFC5654, requirement 5).
  6. The MPLS-TP control plane must support traffic-engineered
     point-to-point (P2P) and point-to-multipoint (P2MP) transport
     paths (RFC5654, requirement 6).
  7. The MPLS-TP control plane must support unidirectional,
     associated bidirectional and co-routed bidirectional point-to-
     point transport paths (RFC5654, requirement 7).
  8. The MPLS-TP control plane must support unidirectional point-to-
     multipoint transport paths (RFC5654, requirement 8).
  9. The MPLS-TP control plane must enable all nodes (i.e., ingress,
     egress, and intermediate) to be aware about the pairing
     relationship of the forward and the backward directions
     belonging to the same co-routed bidirectional transport path
     (RFC5654, requirement 10).
 10. The MPLS-TP control plane must enable edge nodes (i.e., ingress
     and egress) to be aware of the pairing relationship of the
     forward and the backward directions belonging to the same
     associated bidirectional transport path (RFC5654, requirement
     11).
 11. The MPLS-TP control plane should enable common transit nodes to
     be aware of the pairing relationship of the forward and the
     backward directions belonging to the same associated
     bidirectional transport path (RFC5654, requirement 12).
 12. The MPLS-TP control plane must support bidirectional transport
     paths with symmetric bandwidth requirements, i.e., the amount
     of reserved bandwidth is the same in the forward and backward
     directions (RFC5654, requirement 13).
 13. The MPLS-TP control plane must support bidirectional transport
     paths with asymmetric bandwidth requirements, i.e., the amount
     of reserved bandwidth differs in the forward and backward
     directions (RFC5654, requirement 14).
 14. The MPLS-TP control plane must support the logical separation
     of the control plane from the management and data planes
     (RFC5654, requirement 15).  Note that this implies that the
     addresses used in the control plane are independent from the
     addresses used in the management and data planes.
 15. The MPLS-TP control plane must support the physical separation
     of the control plane from the management and data plane, and no
     assumptions should be made about the state of the data-plane
     channels from information about the control- or management-
     plane channels when they are running out-of-band (RFC5654,
     requirement 16).
 16. A control plane must be defined to support dynamic provisioning
     and restoration of MPLS-TP transport paths, but its use is a
     network operator's choice (RFC5654, requirement 18).
 17. The presence of a control plane must not be required for static
     provisioning of MPLS-TP transport paths (RFC5654, requirement
     19).
 18. The MPLS-TP control plane must permit the coexistence of
     statically and dynamically provisioned/managed MPLS-TP
     transport paths within the same layer network or domain
     (RFC5654, requirement 20).
 19. The MPLS-TP control plane should be operable in a way that is
     similar to the way the control plane operates in other
     transport-layer technologies (RFC5654, requirement 21).
 20. The MPLS-TP control plane must avoid or minimize traffic impact
     (e.g., packet delay, reordering, and loss) during network
     reconfiguration (RFC5654, requirement 24).
 21. The MPLS-TP control plane must work across multiple homogeneous
     domains (RFC5654, requirement 25), i.e., all domains use the
     same MPLS-TP control plane.
 22. The MPLS-TP control plane should work across multiple non-
     homogeneous domains (RFC5654, requirement 26), i.e., some
     domains use the same control plane and other domains use static
     provisioning at the domain boundary.
 23. The MPLS-TP control plane must not dictate any particular
     physical or logical topology (RFC5654, requirement 27).
 24. The MPLS-TP control plane must include support of ring
     topologies that may be deployed with arbitrary interconnection
     and support of rings of at least 16 nodes (RFC5654,
     requirements 27.A, 27.B, and 27.C).
 25. The MPLS-TP control plane must scale gracefully to support a
     large number of transport paths, nodes, and links.  That is, it
     must be able to scale at least as well as control planes in
     existing transport technologies with growing and increasingly
     complex network topologies as well as with increasing bandwidth
     demands, number of customers, and number of services
     (RFC5654, requirements 53 and 28).
 26. The MPLS-TP control plane should not provision transport paths
     that contain forwarding loops (RFC5654, requirement 29).
 27. The MPLS-TP control plane must support multiple client layers
     (e.g., MPLS-TP, IP, MPLS, Ethernet, ATM, Frame Relay, etc.)
     (RFC5654, requirement 30).
 28. The MPLS-TP control plane must provide a generic and extensible
     solution to support the transport of MPLS-TP transport paths
     over one or more server-layer networks (such as MPLS-TP,
     Ethernet, Synchronous Optical Network / Synchronous Digital
     Hierarchy (SONET/SDH), Optical Transport Network (OTN), etc.).
     Requirements for bandwidth management within a server-layer
     network are outside the scope of this document (RFC5654,
     requirement 31).
 29. In an environment where an MPLS-TP layer network is supporting
     a client-layer network, and the MPLS-TP layer network is
     supported by a server-layer network, then the control-plane
     operation of the MPLS-TP layer network must be possible without
     any dependencies on the server or client-layer network
     (RFC5654, requirement 32).
 30. The MPLS-TP control plane must allow for the transport of a
     client MPLS or MPLS-TP layer network over a server MPLS or
     MPLS-TP layer network (RFC5654, requirement 33).
 31. The MPLS-TP control plane must allow the autonomous operation
     of the layers of a multi-layer network that includes an MPLS-TP
     layer (RFC5654, requirement 34).
 32. The MPLS-TP control plane must allow the hiding of MPLS-TP
     layer network addressing and other information (e.g., topology)
     from client-layer networks.  However, it should be possible, at
     the option of the operator, to leak a limited amount of
     summarized information, such as Shared Risk Link Groups (SRLGs)
     or reachability, between layers (RFC5654, requirement 35).
 33. The MPLS-TP control plane must allow for the identification of
     a transport path on each link within and at the destination
     (egress) of the transport network (RFC5654, requirements 38
     and 39).
 34. The MPLS-TP control plane must allow for the use of P2MP server
     (sub-)layer capabilities as well as P2P server (sub-)layer
     capabilities when supporting P2MP MPLS-TP transport paths
     (RFC5654, requirement 40).
 35. The MPLS-TP control plane must be extensible in order to
     accommodate new types of client-layer networks and services
     (RFC5654, requirement 41).
 36. The MPLS-TP control plane should support the reserved bandwidth
     associated with a transport path to be increased without
     impacting the existing traffic on that transport path, provided
     enough resources are available (RFC5654, requirement 42)).
 37. The MPLS-TP control plane should support the reserved bandwidth
     of a transport path being decreased without impacting the
     existing traffic on that transport path, provided that the
     level of existing traffic is smaller than the reserved
     bandwidth following the decrease (RFC5654, requirement 43).
 38. The control plane for MPLS-TP must fit within the ASON
     (control-plane) architecture.  The ITU-T has defined an
     architecture for ASONs in G.8080 [ITU.G8080.2006] and G.8080
     Amendment 1 [ITU.G8080.2008].  An interpretation of the ASON
     signaling and routing requirements in the context of GMPLS can
     be found in RFC4139, RFC4258, and Section 2.4, paragraphs 2
     and 3 of RFC5654.
 39. The MPLS-TP control plane must support control-plane topology
     and data-plane topology independence (RFC5654, requirement
     47).
 40. A failure of the MPLS-TP control plane must not interfere with
     the delivery of service or recovery of established transport
     paths (RFC5654, requirement 47).
 41. The MPLS-TP control plane must be able to operate independent
     of any particular client- or server-layer control plane
     (RFC5654, requirement 48).
 42. The MPLS-TP control plane should support, but not require, an
     integrated control plane encompassing MPLS-TP together with its
     server- and client-layer networks when these layer networks
     belong to the same administrative domain (RFC5654,
     requirement 49).
 43. The MPLS-TP control plane must support configuration of
     protection functions and any associated maintenance (OAM)
     functions (RFC5654, requirements 50 and 7).
 44. The MPLS-TP control plane must support the configuration and
     modification of OAM maintenance points as well as the
     activation/deactivation of OAM when the transport path or
     transport service is established or modified (RFC5654,
     requirement 51).
 45. The MPLS-TP control plane must be capable of restarting and
     relearning its previous state without impacting forwarding
     (RFC5654, requirement 54).
 46. The MPLS-TP control plane must provide a mechanism for dynamic
     ownership transfer of the control of MPLS-TP transport paths
     from the management plane to the control plane and vice versa.
     The number of reconfigurations required in the data plane must
     be minimized; preferably no data-plane reconfiguration will be
     required (RFC5654, requirement 55).  Note, such transfers
     cover all transport path control functions including control of
     recovery and OAM.
 47. The MPLS-TP control plane must support protection and
     restoration mechanisms, i.e., recovery (RFC5654, requirement
     52).
     Note that the MPLS-TP survivability framework document
     RFC6372 provides additional useful information related to
     recovery.
 48. The MPLS-TP control-plane mechanisms should be identical (or as
     similar as possible) to those already used in existing
     transport networks to simplify implementation and operations.
     However, this must not override any other requirement
     (RFC5654, requirement 56 A).
 49. The MPLS-TP control-plane mechanisms used for P2P and P2MP
     recovery should be identical to simplify implementation and
     operation.  However, this must not override any other
     requirement (RFC5654, requirement 56 B).
 50. The MPLS-TP control plane must support recovery mechanisms that
     are applicable at various levels throughout the network
     including support for link, transport path, segment,
     concatenated segment, and end-to-end recovery (RFC5654,
     requirement 57).
 51. The MPLS-TP control plane must support recovery paths that meet
     the Service Level Agreement (SLA) protection objectives of the
     service (RFC5654, requirement 58).  These include:
     a. Guarantee 50-ms recovery times from the moment of fault
        detection in networks with spans less than 1200 km.
     b. Protection of 100% of the traffic on the protected path.
     c. Recovery must meet SLA requirements over multiple domains.
 52. The MPLS-TP control plane should support per-transport-path
     recovery objectives (RFC5654, requirement 59).
 53. The MPLS-TP control plane must support recovery mechanisms that
     are applicable to any topology (RFC5654, requirement 60).
 54. The MPLS-TP control plane must operate in synergy with
     (including coordination of timing/timer settings) the recovery
     mechanisms present in any client or server transport networks
     (for example, Ethernet, SDH, OTN, Wavelength Division
     Multiplexing (WDM)) to avoid race conditions between the layers
     (RFC5654, requirement 61).
 55. The MPLS-TP control plane must support recovery and reversion
     mechanisms that prevent frequent operation of recovery in the
     event of an intermittent defect (RFC5654, requirement 62).
 56. The MPLS-TP control plane must support revertive and non-
     revertive protection behavior (RFC5654, requirement 64).
 57. The MPLS-TP control plane must support 1+1 bidirectional
     protection for P2P transport paths (RFC5654, requirement 65
     A).
 58. The MPLS-TP control plane must support 1+1 unidirectional
     protection for P2P transport paths (RFC5654, requirement 65
     B).
 59. The MPLS-TP control plane must support 1+1 unidirectional
     protection for P2MP transport paths (RFC5654, requirement 65
     C).
 60. The MPLS-TP control plane must support the ability to share
     protection resources amongst a number of transport paths
     (RFC5654, requirement 66).
 61. The MPLS-TP control plane must support 1:n bidirectional
     protection for P2P transport paths.  Bidirectional 1:n
     protection should be the default for 1:n protection (RFC5654,
     requirement 67 A).
 62. The MPLS-TP control plane must support 1:n unidirectional
     protection for P2MP transport paths (RFC5654, requirement 67
     B).
 63. The MPLS-TP control plane may support 1:n unidirectional
     protection for P2P transport paths (RFC5654, requirement 65
     C).
 64. The MPLS-TP control plane may support the control of extra-
     traffic type traffic (RFC5654, note after requirement 67).
 65. The MPLS-TP control plane should support 1:n (including 1:1)
     shared mesh recovery (RFC5654, requirement 68).
 66. The MPLS-TP control plane must support sharing of protection
     resources such that protection paths that are known not to be
     required concurrently can share the same resources (RFC5654,
     requirement 69).
 67. The MPLS-TP control plane must support the sharing of resources
     between a restoration transport path and the transport path
     being replaced (RFC5654, requirement 70).
 68. The MPLS-TP control plane must support restoration priority so
     that an implementation can determine the order in which
     transport paths should be restored (RFC5654, requirement 71).
 69. The MPLS-TP control plane must support preemption priority in
     order to allow restoration to displace other transport paths in
     the event of resource constraints (RFC5654, requirements 72
     and 86).
 70. The MPLS-TP control plane must support revertive and non-
     revertive restoration behavior (RFC5654, requirement 73).
 71. The MPLS-TP control plane must support recovery being triggered
     by physical (lower) layer fault indications (RFC5654,
     requirement 74).
 72. The MPLS-TP control plane must support recovery being triggered
     by OAM (RFC5654, requirement 75).
 73. The MPLS-TP control plane must support management-plane
     recovery triggers (e.g., forced switch, etc.) (RFC5654,
     requirement 76).
 74. The MPLS-TP control plane must support the differentiation of
     administrative recovery actions from recovery actions initiated
     by other triggers (RFC5654, requirement 77).
 75. The MPLS-TP control plane should support control-plane
     restoration triggers (e.g., forced switch, etc.) (RFC5654,
     requirement 78).
 76. The MPLS-TP control plane must support priority logic to
     negotiate and accommodate coexisting requests (i.e., multiple
     requests) for protection switching (e.g., administrative
     requests and requests due to link/node failures) (RFC5654,
     requirement 79).
 77. The MPLS-TP control plane must support the association of
     protection paths and working paths (sometimes known as
     protection groups) (RFC5654, requirement 80).
 78. The MPLS-TP control plane must support pre-calculation of
     recovery paths (RFC5654, requirement 81).
 79. The MPLS-TP control plane must support pre-provisioning of
     recovery paths (RFC5654, requirement 82).
 80. The MPLS-TP control plane must support the external commands
     defined in RFC4427.  External controls overruled by higher
     priority requests (e.g., administrative requests and requests
     due to link/node failures) or unable to be signaled to the
     remote end (e.g., because of a protection state coordination
     fail) must be ignored/dropped (RFC5654, requirement 83).
 81. The MPLS-TP control plane must permit the testing and
     validation of the integrity of the protection/recovery
     transport path (RFC5654, requirement 84 A).
 82. The MPLS-TP control plane must permit the testing and
     validation of protection/restoration mechanisms without
     triggering the actual protection/restoration (RFC5654,
     requirement 84 B).
 83. The MPLS-TP control plane must permit the testing and
     validation of protection/restoration mechanisms while the
     working path is in service (RFC5654, requirement 84 C).
 84. The MPLS-TP control plane must permit the testing and
     validation of protection/restoration mechanisms while the
     working path is out of service (RFC5654, requirement 84 D).
 85. The MPLS-TP control plane must support the establishment and
     maintenance of all recovery entities and functions (RFC5654,
     requirement 89 A).
 86. The MPLS-TP control plane must support signaling of recovery
     administrative control (RFC5654, requirement 89 B).
 87. The MPLS-TP control plane must support protection state
     coordination.  Since control-plane network topology is
     independent from the data-plane network topology, the
     protection state coordination supported by the MPLS-TP control
     plane may run on resources different than the data-plane
     resources handled within the recovery mechanism (e.g., backup)
     (RFC5654, requirement 89 C).
 88. When present, the MPLS-TP control plane must support recovery
     mechanisms that are optimized for specific network topologies.
     These mechanisms must be interoperable with the mechanisms
     defined for arbitrary topology (mesh) networks to enable
     protection of end-to-end transport paths (RFC5654,
     requirement 91).
 89. When present, the MPLS-TP control plane must support the
     control of ring-topology-specific recovery mechanisms
     (RFC5654, Section 2.5.6.1).
 90. The MPLS-TP control plane must include support for
     differentiated services and different traffic types with
     traffic class separation associated with different traffic
     (RFC5654, requirement 110).
 91. The MPLS-TP control plane must support the provisioning of
     services that provide guaranteed Service Level Specifications
     (SLSs), with support for hard (RFC3209 style) and relative
     (RFC3270 style) end-to-end bandwidth guarantees (RFC5654,
     requirement 111).
 92. The MPLS-TP control plane must support the provisioning of
     services that are sensitive to jitter and delay (RFC5654,
     requirement 112).

Requirements Derived from the MPLS-TP Framework

The following additional requirements are based on RFC5921, [TP-P2MP-FWK], and RFC5960:

 93. Per-packet Equal Cost Multi-Path (ECMP) load balancing is
     currently outside the scope of MPLS-TP (RFC5960, Section
     3.1.1, paragraph 6).
 94. Penultimate Hop Popping (PHP) must be disabled on MPLS-TP LSPs
     by default (RFC5960, Section 3.1.1, paragraph 7).
 95. The MPLS-TP control plane must support both E-LSP (Explicitly
     TC-encoded-PSC LSP) and L-LSP (Label-Only-Inferred-PSC LSP)
     MPLS Diffserv modes as specified in RFC3270, RFC5462, and
     Section 3.3.2, paragraph 12 of RFC5960.
 96. Both Single-Segment PWs (see RFC3985) and Multi-Segment PWs
     (see RFC5659) shall be supported by the MPLS-TP control
     plane.  MPLS-TP shall use the definition of Multi-Segment PWs
     as defined by the IETF (RFC5921, Section 3.4.4).
 97. The MPLS-TP control plane must support the control of PWs and
     their associated labels (RFC5921, Section 3.4.4).
 98. The MPLS-TP control plane must support network-layer clients,
     i.e., clients whose traffic is transported over an MPLS-TP
     network without the use of PWs (RFC5921, Section 3.4.5).
     a. The MPLS-TP control plane must support the use of network-
        layer protocol-specific LSPs and labels (RFC5921, Section
        3.4.5).
     b. The MPLS-TP control plane must support the use of a client-
        service-specific LSPs and labels (RFC5921, Section 3.4.5).
 99. The MPLS-TP control plane for LSPs must be based on the GMPLS
     control plane.  More specifically, GMPLS RSVP-TE RFC3473 and
     related extensions are used for LSP signaling, and GMPLS OSPF-
     TE RFC5392 and ISIS-TE RFC5316 are used for routing
     (RFC5921, Section 3.9).
100. The MPLS-TP control plane for PWs must be based on the MPLS
     control plane for PWs, and more specifically, targeted LDP (T-
     LDP) RFC4447 is used for PW signaling (RFC5921, Section
     3.9, paragraph 5).
101. The MPLS-TP control plane must ensure its own survivability and
     be able to recover gracefully from failures and degradations.
     These include graceful restart and hot redundant configurations
     (RFC5921, Section 3.9, paragraph 16).
102. The MPLS-TP control plane must support linear, ring, and meshed
     protection schemes (RFC5921, Section 3.12, paragraph 3).
103. The MPLS-TP control plane must support the control of SPMEs
     (hierarchical LSPs) for new or existing end-to-end LSPs
     (RFC5921, Section 3.12, paragraph 7).

Requirements Derived from the OAM Framework

The following additional requirements are based on RFC5860 and RFC6371:

104. The MPLS-TP control plane must support the capability to
     enable/disable OAM functions as part of service establishment
     (RFC5860, Section 2.1.6, paragraph 1.  Note that OAM
     functions are applicable regardless of the label stack depth
     (i.e., level of LSP hierarchy or PW) (RFC5860, Section 2.1.1,
     paragraph 3).
105. The MPLS-TP control plane must support the capability to
     enable/disable OAM functions after service establishment.  In
     such cases, the customer must not perceive service degradation
     as a result of OAM enabling/disabling (RFC5860, Section
     2.1.6, paragraphs 1 and 2).
106. The MPLS-TP control plane must support dynamic control of any
     of the existing IP/MPLS and PW OAM protocols, e.g., LSP-Ping
     RFC4379, MPLS-BFD RFC5884, VCCV RFC5085, and VCCV-BFD
     RFC5885 (RFC5860, Section 2.1.4, paragraph 2).
107. The MPLS-TP control plane must allow for the ability to support
     experimental OAM functions.  These functions must be disabled
     by default (RFC5860, Section 2.2, paragraph 2).
108. The MPLS-TP control plane must support the choice of which (if
     any) OAM function(s) to use and to which PW, LSP or Section it
     applies (RFC5860, Section 2.2, paragraph 3).
109. The MPLS-TP control plane must allow (e.g., enable/disable)
     mechanisms that support the localization of faults and the
     notification of appropriate nodes (RFC5860, Section 2.2.1,
     paragraph 1).
110. The MPLS-TP control plane may support mechanisms that permit
     the service provider to be informed of a fault or defect
     affecting the service(s) it provides, even if the fault or
     defect is located outside of his domain (RFC5860, Section
     2.2.1, paragraph 2).
111. Information exchange between various nodes involved in the
     MPLS-TP control plane should be reliable such that, for
     example, defects or faults are properly detected or that state
     changes are effectively known by the appropriate nodes
     (RFC5860, Section 2.2.1, paragraph 3).
112. The MPLS-TP control plane must provide functionality to control
     an end point's ability to monitor the liveness of a PW, LSP, or
     Section (RFC5860, Section 2.2.2, paragraph 1).
113. The MPLS-TP control plane must provide functionality to control
     an end point's ability to determine whether or not it is
     connected to specific end point(s) by means of the expected PW,
     LSP, or Section (RFC5860, Section 2.2.3, paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        an end point's ability to perform this function proactively
        (RFC5860, Section 2.2.3, paragraph 2).
     b. The MPLS-TP control plane must provide mechanisms to control
        an end point's ability to perform this function on-demand
        (RFC5860, Section 2.2.3, paragraph 3).
114. The MPLS-TP control plane must provide functionality to control
     diagnostic testing on a PW, LSP or Section (RFC5860, Section
     2.2.5, paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        the performance of this function on-demand (RFC5860,
        Section 2.2.5, paragraph 2).
115. The MPLS-TP control plane must provide functionality to enable
     an end point to discover the Intermediate Point(s) (if any) and
     end point(s) along a PW, LSP, or Section, and more generally to
     trace (record) the route of a PW, LSP, or Section (RFC5860,
     Section 2.2.4, paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        the performance of this function on-demand (RFC5860,
        Section 2.2.4, paragraph 2).
116. The MPLS-TP control plane must provide functionality to enable
     an end point of a PW, LSP, or Section to instruct its
     associated end point(s) to lock the PW, LSP, or Section
     (RFC5860, Section 2.2.6, paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        the performance of this function on-demand (RFC5860,
        Section 2.2.6, paragraph 2).
117. The MPLS-TP control plane must provide functionality to enable
     an Intermediate Point of a PW or LSP to report, to an end point
     of that same PW or LSP, a lock condition indirectly affecting
     that PW or LSP (RFC5860, Section 2.2.7, paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        the performance of this function proactively (RFC5860,
        Section 2.2.7, paragraph 2).
118. The MPLS-TP control plane must provide functionality to enable
     an Intermediate Point of a PW or LSP to report, to an end point
     of that same PW or LSP, a fault or defect condition affecting
     that PW or LSP (RFC5860, Section 2.2.8, paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        the performance of this function proactively (RFC5860,
        Section 2.2.8, paragraph 2).
119. The MPLS-TP control plane must provide functionality to enable
     an end point to report, to its associated end point, a fault or
     defect condition that it detects on a PW, LSP, or Section for
     which they are the end points (RFC5860, Section 2.2.9,
     paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        the performance of this function proactively (RFC5860,
        Section 2.2.9, paragraph 2).
120. The MPLS-TP control plane must provide functionality to enable
     the propagation, across an MPLS-TP network, of information
     pertaining to a client defect or fault condition detected at an
     end point of a PW or LSP, if the client-layer mechanisms do not
     provide an alarm notification/propagation mechanism (RFC5860,
     Section 2.2.10, paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        the performance of this function proactively (RFC5860,
        Section 2.2.10, paragraph 2).
121. The MPLS-TP control plane must provide functionality to enable
     the control of quantification of packet loss ratio over a PW,
     LSP, or Section (RFC5860, Section 2.2.11, paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        the performance of this function proactively and on-demand
        (RFC5860, Section 2.2.11, paragraph 4).
122. The MPLS-TP control plane must provide functionality to control
     the quantification and reporting of the one-way, and if
     appropriate, the two-way, delay of a PW, LSP, or Section
     (RFC5860, Section 2.2.12, paragraph 1).
     a. The MPLS-TP control plane must provide mechanisms to control
        the performance of this function proactively and on-demand
        (RFC5860, Section 2.2.12, paragraph 6).
123. The MPLS-TP control plane must support the configuration of OAM
     functional components that include Maintenance Entities (MEs)
     and Maintenance Entity Groups (MEGs) as instantiated in MEPs,
     MIPs, and SPMEs (RFC6371, Section 3.6).
124. For dynamically established transport paths, the control plane
     must support the configuration of OAM operations (RFC6371,
     Section 5).
     a. The MPLS-TP control plane must provide mechanisms to
        configure proactive monitoring for a MEG at, or after,
        transport path creation time.
     b. The MPLS-TP control plane must provide mechanisms to
        configure the operational characteristics of in-band
        measurement transactions (e.g., Connectivity Verification
        (CV), Loss Measurement (LM), etc.) at MEPs (associated with
        a transport path).
     c. The MPLS-TP control plane may provide mechanisms to
        configure server-layer event reporting by intermediate
        nodes.
     d. The MPLS-TP control plane may provide mechanisms to
        configure the reporting of measurements resulting from
        proactive monitoring.
125. The MPLS-TP control plane must support the control of the loss
     of continuity (LOC) traffic block consequent action (RFC6371,
     Section 5.1.2, paragraph 4).
126. For dynamically established transport paths that have a
     proactive Continuity Check and Connectivity Verification (CC-V)
     function enabled, the control plane must support the signaling
     of the following MEP configuration information (RFC6371,
     Section 5.1.3):
     a. The MPLS-TP control plane must provide mechanisms to
        configure the MEG identifier to which the MEP belongs.
     b. The MPLS-TP control plane must provide mechanisms to
        configure a MEP's own identity inside a MEG.
     c. The MPLS-TP control plane must provide mechanisms to
        configure the list of the other MEPs in the MEG.
     d. The MPLS-TP control plane must provide mechanisms to
        configure the CC-V transmission rate / reception period
        (covering all application types).
127. The MPLS-TP control plane must provide mechanisms to configure
     the generation of Alarm Indication Signal (AIS) packets for
     each MEG (RFC6371, Section 5.3, paragraph 9).
128. The MPLS-TP control plane must provide mechanisms to configure
     the generation of Lock Report (LKR) packets for each MEG
     (RFC6371, Section 5.4, paragraph 9).
129. The MPLS-TP control plane must provide mechanisms to configure
     the use of proactive Packet Loss Measurement (LM), and the
     transmission rate and Per-Hop Behavior (PHB) class associated
     with the LM OAM packets originating from a MEP (RFC6371,
     Section 5.5.1, paragraph 1).
130. The MPLS-TP control plane must provide mechanisms to configure
     the use of proactive Packet Delay Measurement (DM), and the
     transmission rate and PHB class associated with the DM OAM
     packets originating from a MEP (RFC6371, Section 5.6.1,
     paragraph 1).
131. The MPLS-TP control plane must provide mechanisms to configure
     the use of Client Failure Indication (CFI), and the
     transmission rate and PHB class associated with the CFI OAM
     packets originating from a MEP (RFC6371, Section 5.7.1,
     paragraph 1).
132. The MPLS-TP control plane should provide mechanisms to control
     the use of on-demand CV packets (RFC6371, Section 6.1).
     a. The MPLS-TP control plane should provide mechanisms to
        configure the number of packets to be transmitted/received
        in each burst of on-demand CV packets and their packet size
        (RFC6371, Section 6.1.1, paragraph 1).
     b. When an on-demand CV packet is used to check connectivity
        toward a target MIP, the MPLS-TP control plane should
        provide mechanisms to configure the number of hops to reach
        the target MIP (RFC6371, Section 6.1.1, paragraph 2).
     c. The MPLS-TP control plane should provide mechanisms to
        configure the PHB of on-demand CV packets (RFC6371,
        Section 6.1.1, paragraph 3).
133. The MPLS-TP control plane should provide mechanisms to control
     the use of on-demand LM, including configuration of the
     beginning and duration of the LM procedures, the transmission
     rate, and PHB associated with the LM OAM packets originating
     from a MEP (RFC6371, Section 6.2.1).
134. The MPLS-TP control plane should provide mechanisms to control
     the use of throughput estimation (RFC6371, Section 6.3.1).
135. The MPLS-TP control plane should provide mechanisms to control
     the use of on-demand DM, including configuration of the
     beginning and duration of the DM procedures, the transmission
     rate, and PHB associated with the DM OAM packets originating
     from a MEP (RFC6371, Section 6.5.1).

Security Requirements

There are no specific MPLS-TP control-plane security requirements. The existing framework for MPLS and GMPLS security is documented in RFC5920, and that document applies equally to MPLS-TP.

Identifier Requirements

The following are requirements based on RFC6370:

136. The MPLS-TP control plane must support MPLS-TP point-to-point
     tunnel identifiers of the forms defined in Section 5.1 of
     RFC6370.
137. The MPLS-TP control plane must support MPLS-TP LSP identifiers
     of the forms defined in Section 5.2 of RFC6370, and the
     mappings to GMPLS as defined in Section 5.3 of RFC6370.
138. The MPLS-TP control plane must support pseudowire path
     identifiers of the form defined in Section 6 of RFC6370.
139. The MPLS-TP control plane must support MEG_IDs for LSPs and PWs
     as defined in Section 7.1.1 of RFC6370.
140. The MPLS-TP control plane must support IP-compatible MEG_IDs
     for LSPs and PWs as defined in Section 7.1.2 of RFC6370.
141. The MPLS-TP control plane must support MEP_IDs for LSPs and PWs
     of the forms defined in Section 7.2.1 of RFC6370.
142. The MPLS-TP control plane must support IP-based MEP_IDs for
     MPLS-TP LSP of the forms defined in Section 7.2.2.1 of
     RFC6370.
143. The MPLS-TP control plane must support IP-based MEP_IDs for
     Pseudowires of the form defined in Section 7.2.2.2 of
     RFC6370.

Relationship of PWs and TE LSPs

The data-plane relationship between PWs and LSPs is inherited from standard MPLS and is reviewed in the MPLS-TP framework RFC5921. Likewise, the control-plane relationship between PWs and LSPs is inherited from standard MPLS. This relationship is reviewed in this document. The relationship between the PW and LSP control planes in MPLS-TP is the same as the relationship found in the PWE3 Maintenance Reference Model as presented in the PWE3 architecture; see Figure 6 of RFC3985. The PWE3 architecture RFC3985 states: "The PWE3 protocol-layering model is intended to minimize the differences between PWs operating over different PSN types". Additionally, PW control (maintenance) takes place separately from LSP signaling. RFC4447 and [MS-PW-DYNAMIC] provide such extensions for the use of LDP as the control plane for PWs. This control can provide PW control without providing LSP control.

In the context of MPLS-TP, LSP tunnel signaling is provided via GMPLS RSVP-TE. While RSVP-TE could be extended to support PW control much as LDP was extended in RFC4447, such extensions are out of scope of this document. This means that the control of PWs and LSPs will operate largely independently. The main coordination between LSP and PW control will occur within the nodes that terminate PWs or PW segments. See Section 5.3.2 for an additional discussion on such coordination.

It is worth noting that the control planes for PWs and LSPs may be used independently, and that one may be employed without the other. This translates into four possible scenarios: (1) no control plane is employed; (2) a control plane is used for both LSPs and PWs; (3) a control plane is used for LSPs, but not PWs; (4) a control plane is used for PWs, but not LSPs.

The PW and LSP control planes, collectively, must satisfy the MPLS-TP control-plane requirements reviewed in this document. When client services are provided directly via LSPs, all requirements must be satisfied by the LSP control plane. When client services are provided via PWs, the PW and LSP control planes can operate in combination, and some functions may be satisfied via the PW control plane while others are provided to PWs by the LSP control plane. For

example, to support the recovery functions described in RFC6372, this document focuses on the control of the recovery functions at the LSP layer. PW-based recovery is under development at this time and may be used once defined.

TE LSPs

MPLS-TP uses Generalized MPLS (GMPLS) signaling and routing, see RFC3945, as the control plane for LSPs. The GMPLS control plane is based on the MPLS control plane. GMPLS includes support for MPLS labeled data and transport data planes. GMPLS includes most of the transport-centric features required to support MPLS-TP LSPs. This section will first review the features of GMPLS relevant to MPLS-TP LSPs, then identify how specific requirements can be met using existing GMPLS functions, and will conclude with extensions that are anticipated to support the remaining MPLS-TP control-plane requirements.

GMPLS Functions and MPLS-TP LSPs

This section reviews how existing GMPLS functions can be applied to MPLS-TP.

In-Band and Out-of-Band Control

GMPLS supports both in-band and out-of-band control. The terms "in- band" and "out-of-band", in the context of this document, refer to the relationship of the control plane relative to the management and data planes. The terms may be used to refer to the control plane independent of the management plane, or to both of them in concert. The remainder of this section describes the relationship of the control plane to the management and data planes.

There are multiple uses of both terms "in-band" and "out-of-band". The terms may relate to a channel, a path, or a network. Each of these can be used independently or in combination. Briefly, some typical usage of the terms is as follows:

o In-band

  This term is used to refer to cases where control-plane traffic is
  sent in the same communication channel used to transport
  associated user data or management traffic.  IP, MPLS, and
  Ethernet networks are all examples where control traffic is
  typically sent in-band with the data traffic.  An example of this
  case in the context of MPLS-TP is where control-plane traffic is
  sent via the MPLS Generic Associated Channel (G-ACh), see
  RFC5586, using the same LSP as controlled user traffic.

o Out-of-band, in-fiber (same physical connection)

  This term is used to refer to cases where control-plane traffic is
  sent using a different communication channel from the associated
  data or management traffic, and the control communication channel
  resides in the same fiber as either the management or data
  traffic.  An example of this case in the context of MPLS-TP is
  where control-plane traffic is sent via the G-ACh using a
  dedicated LSP on the same link (interface) that carries controlled
  user traffic.

o Out-of-band, aligned topology

  This term is used to refer to the cases where control-plane
  traffic is sent using a different communication channel from the
  associated data or management traffic, and the control traffic
  follows the same node-to-node path as either the data or
  management traffic.
  Such topologies are usually supported using a parallel fiber or
  other configurations where multiple data channels are available
  and one is (dynamically) selected as the control channel.  An
  example of this case in the context of MPLS-TP is where control-
  plane traffic is sent along the same nodal path, but not
  necessarily the same links (interfaces), as the corresponding
  controlled user traffic.

o Out-of-band, independent topology

  This term is used to refer to the cases where control-plane
  traffic is sent using a different communication channel from the
  associated data or management traffic, and the control traffic may
  follow a path that is completely independent of the data traffic.
  Such configurations are a superset of the other cases and do not
  preclude the use of in-fiber or aligned topology links, but
  alignment is not required.  An example of this case in the context
  of MPLS-TP is where control-plane traffic is sent between
  controlling nodes using any available path and links, completely
  without regard for the path(s) taken by corresponding management
  or user traffic.

In the context of MPLS-TP requirements, requirement 14 (see Section 2 above) can be met using out-of-band in-fiber or aligned topology types of control. Requirement 15 can only be met by using out-of- band, independent topology. G-ACh is likely to be used extensively in MPLS-TP networks to support the MPLS-TP control (and management) planes.

Addressing

MPLS-TP reuses and supports the addressing mechanisms supported by MPLS. The MPLS-TP identifiers document (see RFC6370) provides additional context on how IP addresses are used within MPLS-TP. MPLS, and consequently MPLS-TP, uses the IPv4 and IPv6 address families to identify MPLS-TP nodes by default for network management and signaling purposes. The address spaces and neighbor adjacencies in the control, management, and data planes used in an MPLS-TP network may be completely separated or combined at the discretion of an MPLS-TP operator and based on the equipment capabilities of a vendor. The separation of the control and management planes from the data plane allows each plane to be independently addressable. Each plane may use addresses that are not mutually reachable, e.g., it is likely that the data plane will not be able to reach an address from the management or control planes and vice versa. Each plane may also use a different address family. It is even possible to reuse addresses in each plane, but this is not recommended as it may lead to operational confusion. As previously mentioned, the G-ACh mechanism defined in RFC5586 is expected to be used extensively in MPLS-TP networks to support the MPLS-TP control (and management) planes.

Routing

Routing support for MPLS-TP LSPs is based on GMPLS routing. GMPLS routing builds on TE routing and has been extended to support multiple switching technologies per RFC3945 and RFC4202 as well as multiple levels of packet switching within a single network. IS- IS extensions for GMPLS are defined in RFC5307 and RFC5316, which build on the TE extensions to IS-IS defined in RFC5305. OSPF extensions for GMPLS are defined in RFC4203 and RFC5392, which build on the TE extensions to OSPF defined in RFC3630. The listed RFCs should be viewed as a starting point rather than a comprehensive list as there are other IS-IS and OSPF extensions, as defined in IETF RFCs, that can be used within an MPLS-TP network.

TE LSPs and Constraint-Based Path Computation

Both MPLS and GMPLS allow for traffic engineering and constraint- based path computation. MPLS path computation provides paths for MPLS-TE unidirectional P2P and P2MP LSPs. GMPLS path computation adds bidirectional LSPs, explicit recovery path computation, as well as support for the other functions discussed in this section.

Both MPLS and GMPLS path computation allow for the restriction of path selection based on the use of Explicit Route Objects (EROs) and other LSP attributes; see RFC3209 and RFC3473. In all cases, no

specific algorithm is standardized by the IETF. This is anticipated to continue to be the case for MPLS-TP LSPs.

Relation to PCE

Path Computation Element (PCE)-based approaches, see RFC4655, may be used for path computation of a GMPLS LSP, and consequently an MPLS-TP LSP, across domains and in a single domain. In cases where PCE is used, the PCE Communication Protocol (PCEP), see RFC5440, will be used to communicate PCE-related requests and responses. MPLS-TP-specific extensions to PCEP are currently out of scope of the MPLS-TP project and this document.

Signaling

GMPLS signaling is defined in RFC3471 and RFC3473 and is based on RSVP-TE RFC3209. Constraint-based Routed LDP (CR-LDP) GMPLS (see RFC3472) is no longer under active development within the IETF, i.e., it is deprecated (see RFC3468) and must not be used for MPLS nor MPLS-TP consequently. In general, all RSVP-TE extensions that apply to MPLS may also be used for GMPLS and consequently MPLS-TP. Most notably, this includes support for P2MP signaling as defined in RFC4875.

GMPLS signaling includes a number of MPLS-TP required functions -- notably, support for out-of-band control, bidirectional LSPs, and independent control- and data-plane fault management. There are also numerous other GMPLS and MPLS extensions that can be used to provide specific functions in MPLS-TP networks. Specific references are provided below.

Unnumbered Links

Support for unnumbered links (i.e., links that do not have IP addresses) is permitted in MPLS-TP and its usage is at the discretion of the network operator. Support for unnumbered links is included for routing using OSPF RFC4203 and IS-IS RFC5307, and for signaling in RFC3477.

Link Bundling

Link bundling provides a local construct that can be used to improve scaling of TE routing when multiple data links are shared between node pairs. Link bundling for MPLS and GMPLS networks is defined in RFC4201. Link bundling may be used in MPLS-TP networks, and its use is at the discretion of the network operator.

Hierarchical LSPs

This section reuses text from RFC6107.

RFC3031 describes how MPLS labels may be stacked so that LSPs may be nested with one LSP running through another. This concept of hierarchical LSPs (H-LSPs) is formalized in RFC4206 with a set of protocol mechanisms for the establishment of a hierarchical LSP that can carry one or more other LSPs.

RFC4206 goes on to explain that a hierarchical LSP may carry other LSPs only according to their switching types. This is a function of the way labels are carried. In a packet switch capable network, the hierarchical LSP can carry other packet switch capable LSPs using the MPLS label stack.

Signaling mechanisms defined in RFC4206 allow a hierarchical LSP to be treated as a single hop in the path of another LSP. This mechanism is also sometimes known as "non-adjacent signaling", see RFC4208.

A Forwarding Adjacency (FA) is defined in RFC4206 as a data link created from an LSP and advertised in the same instance of the control plane that advertises the TE links from which the LSP is constructed. The LSP itself is called an FA-LSP. FA-LSPs are analogous to MPLS-TP Sections as discussed in RFC5960.

Thus, a hierarchical LSP may form an FA such that it is advertised as a TE link in the same instance of the routing protocol as was used to advertise the TE links that the LSP traverses.

As observed in RFC4206, the nodes at the ends of an FA would not usually have a routing adjacency.

LSP hierarchy is expected to play an important role in MPLS-TP networks, particularly in the context of scaling and recovery as well as supporting SPMEs.

LSP Recovery

GMPLS defines RSVP-TE extensions in support for end-to-end GMPLS LSPs recovery in RFC4872 and segment recovery in RFC4873. GMPLS segment recovery provides a superset of the function in end-to-end recovery. End-to-end recovery can be viewed as a special case of segment recovery where there is a single recovery domain whose borders coincide with the ingress and egress of the LSP, although specific procedures are defined.

The five defined types of recovery defined in GMPLS are:

  - 1+1 bidirectional protection for P2P LSPs
  - 1+1 unidirectional protection for P2MP LSPs
  - 1:n (including 1:1) protection with or without extra traffic
  - Rerouting without extra traffic (sometimes known as soft
    rerouting), including shared mesh restoration
  - Full LSP rerouting

Recovery for MPLS-TP LSPs, as discussed in RFC6372, is signaled using the mechanism defined in RFC4872 and RFC4873. Note that when MEPs are required for the OAM CC function and the MEPs exist at LSP transit nodes, each MEP is instantiated at a hierarchical LSP end point, and protection is provided end-to-end for the hierarchical LSP. (Protection can be signaled using either RFC4872 or RFC4873 defined procedures.) The use of Notify messages to trigger protection switching and recovery is not required in MPLS-TP, as this function is expected to be supported via OAM. However, its use is not precluded.

4.1.10. Control-Plane Reference Points (E-NNI, I-NNI, UNI)

The majority of RFCs about the GMPLS control plane define the control plane from the context of an internal Network-to-Network Interface (I-NNI). In the MPLS-TP context, some operators may choose to deploy signaled interfaces across User-to-Network Interfaces (UNIs) and across inter-provider, external Network-to-Network Interfaces (E-NNIs). Such support is embodied in RFC4208 for UNIs and in RFC5787 for routing areas in support of E-NNIs. This work may require extensions in order to meet the specific needs of an MPLS-TP UNI and E-NNI.

OAM, MEP (Hierarchy), MIP Configuration and Control

MPLS-TP is defined to support a comprehensive set of MPLS-TP OAM functions. The MPLS-TP control plane will not itself provide OAM functions, but it will be used to instantiate and otherwise control MPLS-TP OAM functions.

Specific OAM requirements for MPLS-TP are documented in RFC5860. This document also states that it is required that the control plane be able to configure and control OAM entities. This requirement is not yet addressed by the existing RFCs, but such work is now under way, e.g., [CCAMP-OAM-FWK] and [CCAMP-OAM-EXT].

Many OAM functions occur on a per-LSP basis, are typically in-band, and are initiated immediately after LSP establishment. Hence, it is desirable that such functions be established and activated via the

same control-plane signaling used to set up the LSP, as this effectively synchronizes OAM with the LSP lifetime and avoids the extra overhead and potential errors associated with separate OAM configuration mechanisms.

Management-Plane Support

There is no MPLS-TP requirement for a standardized management interface to the MPLS-TP control plane. That said, MPLS and GMPLS support a number of standardized management functions. These include the MPLS-TE/GMPLS TE Database Management Information Base [TE-MIB]; the MPLS-TE MIB RFC3812; the MPLS LSR MIB RFC3813; the GMPLS TE MIB RFC4802; and the GMPLS LSR MIB RFC4803. These MIB modules may be used in MPLS-TP networks. A general overview of MPLS-TP related MIB modules can be found in [TP-MIB]. Network management requirements for MPLS-based transport networks are provided in RFC5951.

Recovery Triggers

The GMPLS control plane allows for management-plane recovery triggers and directly supports control-plane recovery triggers. Support for control-plane recovery triggers is defined in RFC4872, which refers to the triggers as "Recovery Commands". These commands can be used with both end-to-end and segment recovery, but are always controlled on an end-to-end basis. The recovery triggers/commands defined in RFC4872 are:

  a. Lockout of recovery LSP
  b. Lockout of normal traffic
  c. Forced switch for normal traffic
  d. Requested switch for normal traffic
  e. Requested switch for recovery LSP

Note that control-plane triggers are typically invoked in response to a management-plane request at the ingress.

Management-Plane / Control-Plane Ownership Transfer

In networks where both the control plane and management plane are provided, LSP provisioning can be done either by the control plane or management plane. As mentioned in the requirements section above, it must be possible to transfer, or handover, a management-plane-created LSP to the control-plane domain and vice versa. RFC5493 defines

the specific requirements for an LSP ownership handover procedure. It must be possible for the control plane to provide the management plane, in a reliable manner, with the status or result of an operation performed by the management plane. This notification may be either synchronous or asynchronous with respect to the operation. Moreover, it must be possible for the management plane to monitor the status of the control plane, for example, the status of a TE link, its available resources, etc. This monitoring may be based on queries initiated by the management plane or on notifications generated by the control plane. A mechanism must be made available by the control plane to the management plane to log operation of a control-plane LSP; that is, it must be possible from the NMS to have a clear view of the life (traffic hit, action performed, signaling, etc.) of a given LSP. The LSP handover procedure for MPLS-TP LSPs is supported via RFC5852.

GMPLS and MPLS-TP Requirements Table

The following table shows how the MPLS-TP control-plane requirements can be met using the existing GMPLS control plane (which builds on the MPLS control plane). Areas where additional specifications are required are also identified. The table lists references based on the control-plane requirements as identified and numbered above in Section 2.

+=======+===========================================================+ | Req # | References | +-------+-----------------------------------------------------------+ | 1 | Generic requirement met by using Standards Track RFCs | | 2 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 | | 3 | RFC5145 + Formal Definition (See Section 4.4.1) | | 4 | Generic requirement met by using Standards Track RFCs | | 5 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 | | 6 | RFC3471, RFC3473, RFC4875 | | 7 | RFC3471, RFC3473 + | | | Associated bidirectional LSPs (See Section 4.4.2) | | 8 | RFC4875 | | 9 | RFC3473 | | 10 | Associated bidirectional LSPs (See Section 4.4.2) | | 11 | Associated bidirectional LSPs (See Section 4.4.2) | | 12 | RFC3473 | | 13 | RFC5467 (Currently Experimental; See Section 4.4.3) | | 14 | RFC3945, RFC3473, RFC4202, RFC4203, RFC5307 | | 15 | RFC3945, RFC3473, RFC4202, RFC4203, RFC5307 | | 16 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 | | 17 | RFC3945, RFC4202 + proper vendor implementation | | 18 | RFC3945, RFC4202 + proper vendor implementation | | 19 | RFC3945, RFC4202 |

| 20 | RFC3473 | | 21 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307, | | | RFC5151 | | 22 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307, | | | RFC5151 | | 23 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 | | 24 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 | | 25 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307, | | | RFC6107 | | 26 | RFC3473, RFC4875 | | 27 | RFC3473, RFC4875 | | 28 | RFC3945, RFC3471, RFC4202 | | 29 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 | | 30 | RFC3945, RFC3471, RFC4202 | | 31 | RFC3945, RFC3471, RFC4202 | | 32 | RFC4208, RFC4974, RFC5787, RFC6001 | | 33 | RFC3473, RFC4875 | | 34 | RFC4875 | | 35 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 | | 36 | RFC3473, RFC3209 (Make-before-break) | | 37 | RFC3473, RFC3209 (Make-before-break) | | 38 | RFC4139, RFC4258, RFC5787 | | 39 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 | | 40 | RFC3473, RFC5063 | | 41 | RFC3945, RFC3471, RFC4202, RFC4208 | | 42 | RFC3945, RFC3471, RFC4202 | | 43 | RFC4872, RFC4873, [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] | | 44 | RFC6107, [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] | | 45 | RFC3473, RFC4203, RFC5307, RFC5063 | | 46 | RFC5493 | | 47 | RFC4872, RFC4873 | | 48 | RFC3945, RFC3471, RFC4202 | | 49 | RFC4872, RFC4873 + Recovery for P2MP (see Sec. 4.4.4) | | 50 | RFC4872, RFC4873 | | 51 | RFC4872, RFC4873 + proper vendor implementation | | 52 | RFC4872, RFC4873, [GMPLS-PS] | | 53 | RFC4872, RFC4873 | | 54 | RFC3473, RFC4872, RFC4873, [GMPLS-PS] | | | Timers are a local implementation matter | | 55 | RFC4872, RFC4873, [GMPLS-PS] + | | | implementation of timers | | 56 | RFC4872, RFC4873, [GMPLS-PS] | | 57 | RFC4872, RFC4873 | | 58 | RFC4872, RFC4873 | | 59 | RFC4872, RFC4873 | | 60 | RFC4872, RFC4873, RFC6107 | | 61 | RFC4872, RFC4873 | | 62 | RFC4872, RFC4873 + Recovery for P2MP (see Sec. 4.4.4) |

| 63 | RFC4872, RFC4873 | | 64 | RFC4872, RFC4873 | | 65 | RFC4872, RFC4873 | | 66 | RFC4872, RFC4873, RFC6107 | | 67 | RFC4872, RFC4873 | | 68 | RFC3473, RFC4872, RFC4873 | | 69 | RFC3473 | | 70 | RFC3473, RFC4872, [GMPLS-PS] | | 71 | RFC3473, RFC4872 | | 72 | RFC4872, RFC4873, [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] | | 73 | RFC4426, RFC4872, RFC4873 | | 74 | RFC4426, RFC4872, RFC4873 | | 75 | RFC4426, RFC4872, RFC4873 | | 76 | RFC4426, RFC4872, RFC4873 | | 77 | RFC4426, RFC4872, RFC4873 | | 78 | RFC4426, RFC4872, RFC4873 + vendor implementation | | 79 | RFC4426, RFC4872, RFC4873 | | 80 | RFC4426, RFC4872, RFC4873 | | 81 | RFC4872, RFC4873 + Testing control (See Sec. 4.4.5) | | 82 | RFC4872, RFC4873 + Testing control (See Sec. 4.4.5) | | 83 | RFC4872, RFC4873 + Testing control (See Sec. 4.4.5) | | 84 | RFC4872, RFC4873 + Testing control (See Sec. 4.4.5) | | 85 | RFC4872, RFC4873, [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] | | 86 | RFC4872, RFC4873 | | 87 | RFC4872, RFC4873 | | 88 | RFC4872, RFC4873, [TP-RING] | | 89 | RFC4872, RFC4873, [TP-RING] | | 90 | RFC3270, RFC3473, RFC4124 + GMPLS Usage (See 4.4.6) | | 91 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 | | 92 | RFC3945, RFC3473, RFC2210, RFC2211, RFC2212 | | 93 | Generic requirement on data plane (correct implementation)| | 94 | RFC3473, [NO-PHP] | | 95 | RFC3270, RFC3473, RFC4124 + GMPLS Usage (See 4.4.6) | | 96 | PW only requirement; see PW Requirements Table (5.2) | | 97 | PW only requirement; see PW Requirements Table (5.2) | | 98 | RFC3945, RFC3473, RFC6107 | | 99 | RFC3945, RFC4202, RFC3473, RFC4203, RFC5307 + | | | RFC5392 and RFC5316 | | 100 | PW only requirement; see PW Requirements Table (5.2) | | 101 | RFC3473, RFC4203, RFC5307, RFC5063 | | 102 | RFC4872, RFC4873, [TP-RING] | | 103 | RFC3945, RFC3473, RFC6107 | | 104 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] | | 105 | RFC3473, [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] | | 106 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] | | 107 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] + (See Sec. 4.4.5) | | 108 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] | | 109 | RFC3473, RFC4872, RFC4873 |

| 110 | RFC3473, RFC4872, RFC4873 | | 111 | RFC3473, RFC4783 | | 112 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] | | 113 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] + (See Sec. 4.4.5) | | 114 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] + (See Sec. 4.4.5) | | 115 | RFC3473 | | 116 | RFC4426, RFC4872, RFC4873 | | 117 | RFC3473, RFC4872, RFC4873 | | 118 | RFC3473, RFC4783 | | 119 | RFC3473 | | 120 | RFC3473, RFC4783 | | 121 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] + (See Sec. 4.4.5) | | 122 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] + (See Sec. 4.4.5) | | 123 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT], RFC6107 | | 124 - | | | 135 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] + (See Sec. 4.4.5) | | 136a | RFC3473 | | 136b | RFC3473 + (See Sec. 4.4.7) | | 137a | RFC3473 | | 137b | RFC3473 + (See Sec. 4.4.7) | | 138 | PW only requirement; see PW Requirements Table (5.2) | | 139 - | | | 143 | [CCAMP-OAM-FWK], [CCAMP-OAM-EXT] + (See Sec. 4.4.8) | +=======+===========================================================+

           Table 1: GMPLS and MPLS-TP Requirements Table

Anticipated MPLS-TP-Related Extensions and Definitions

This section identifies the extensions and other documents that have been identified as likely to be needed to support the full set of MPLS-TP control-plane requirements.

MPLS-TE to MPLS-TP LSP Control-Plane Interworking

While no interworking function is expected in the data plane to support the interconnection of MPLS-TE and MPLS-TP networking, this is not the case for the control plane. MPLS-TE networks typically use LSP signaling based on RFC3209, while MPLS-TP LSPs will be signaled using GMPLS RSVP-TE, i.e., RFC3473. RFC5145 identifies a set of solutions that are aimed to aid in the interworking of MPLS- TE and GMPLS control planes. RFC5145 work will serve as the foundation for a formal definition of MPLS to MPLS-TP control-plane interworking.

Associated Bidirectional LSPs

GMPLS signaling, RFC3473, supports unidirectional and co-routed, bidirectional point-to-point LSPs. MPLS-TP also requires support for associated bidirectional point-to-point LSPs. Such support will require an extension or a formal definition of how the LSP end points supporting an associated bidirectional service will coordinate the two LSPs used to provide such a service. Per requirement 11, transit nodes that support an associated bidirectional service should be aware of the association of the LSPs used to support the service when both LSPs are supported on that transit node. There are several existing protocol mechanisms on which to base such support, including, but not limited to:

  o  GMPLS calls RFC4974.
  o  The ASSOCIATION object RFC4872.
  o  The LSP_TUNNEL_INTERFACE_ID object RFC6107.

Asymmetric Bandwidth LSPs

RFC5467 defines support for bidirectional LSPs that have different (asymmetric) bandwidth requirements for each direction. That RFC can be used to meet the related MPLS-TP technical requirement, but it is currently an Experimental RFC. To fully satisfy the MPLS-TP requirement, RFC 5467 will need to become a Standards Track RFC.

Recovery for P2MP LSPs

The definitions of P2MP, RFC4875, and GMPLS recovery, RFC4872 and RFC4873, do not explicitly cover their interactions. MPLS-TP requires a formal definition of recovery techniques for P2MP LSPs. Such a formal definition will be based on existing RFCs and may not require any new protocol mechanisms but, nonetheless, must be documented.

Test Traffic Control and Other OAM Functions

[CCAMP-OAM-FWK] and [CCAMP-OAM-EXT] are examples of OAM-related control extensions to GMPLS. These extensions cover a portion of, but not all, OAM-related control functions that have been identified in the context of MPLS-TP. As discussed above, the MPLS-TP control plane must support the selection of which OAM function(s) (if any) to use (including support to select experimental OAM functions) and what OAM functionality to run, including Continuity Check (CC),

Connectivity Verification (CV), packet loss, delay quantification, and diagnostic testing of a service. Such support may be included in the listed documents or in other documents.

Diffserv Object Usage in GMPLS

RFC3270 and RFC4124 define support for Diffserv-enabled MPLS LSPs. While RFC4124 references GMPLS signaling, there is no explicit discussion on the use of the Diffserv-related objects in GMPLS signaling. A (possibly Informational) document on how GMPLS supports Diffserv LSPs is likely to prove useful in the context of MPLS-TP.

Support for MPLS-TP LSP Identifiers

MPLS-TP uses two forms of LSP identifiers, see RFC6370. One form is based on existing GMPLS fields. The other form is based on either the globally unique Attachment Interface Identifier (AII) defined in RFC5003 or the ITU Carrier Code (ICC) defined in ITU-T Recommendation M.1400. Neither form is currently supported in GMPLS, and such extensions will need to be documented.

Support for MPLS-TP Maintenance Identifiers

MPLS-TP defines several forms of maintenance-entity-related identifiers. Both node-unique and global forms are defined. Extensions will be required to GMPLS to support these identifiers. These extensions may be added to existing works in progress, such as [CCAMP-OAM-FWK] and [CCAMP-OAM-EXT], or may be defined in independent documents.

Pseudowires

LDP Functions and Pseudowires

MPLS PWs are defined in RFC3985 and RFC5659, and provide for emulated services over an MPLS Packet Switched Network (PSN). Several types of PWs have been defined: (1) Ethernet PWs providing for Ethernet port or Ethernet VLAN transport over MPLS RFC4448, (2) High-Level Data Link Control (HDLC) / PPP PW providing for HDLC/PPP leased line transport over MPLS RFC4618, (3) ATM PWs RFC4816, (4) Frame Relay PWs RFC4619, and (5) circuit Emulation PWs RFC4553.

Today's transport networks based on Plesiochronous Digital Hierarchy (PDH), WDM, or SONET/SDH provide transport for PDH or SONET (e.g., ATM over SONET or Packet PPP over SONET) client signals with no payload awareness. Implementing PW capability allows for the use of an existing technology to substitute the Time-Division Multiplexing

(TDM) transport with packet-based transport, using well-defined PW encapsulation methods for carrying various packet services over MPLS, and providing for potentially better bandwidth utilization.

There are two general classes of PWs: (1) Single-Segment Pseudowires (SS-PWs) RFC3985 and (2) Multi-segment Pseudowires (MS-PWs) RFC5659. An MPLS-TP network domain may transparently transport a PW whose end points are within a client network. Alternatively, an MPLS-TP edge node may be the Terminating PE (T-PE) for a PW, performing adaptation from the native attachment circuit technology (e.g., Ethernet 802.1Q) to an MPLS PW that is then transported in an LSP over an MPLS-TP network. In this way, the PW is analogous to a transport channel in a TDM network, and the LSP is equivalent to a container of multiple non-concatenated channels, albeit they are packet containers. An MPLS-TP network may also contain Switching PEs (S-PEs) for a Multi-Segment PW whereby the T-PEs may be at the edge of an MPLS-TP network or in a client network. In the latter case, a T-PE in a client network performs the adaptation of the native service to MPLS and the MPLS-TP network performs pseudowire switching.

The SS-PW signaling control plane is based on targeted LDP (T-LDP) with specific procedures defined in RFC4447. The MS-PW signaling control plane is also based on T-LDP as allowed for in RFC5659, RFC6073, and [MS-PW-DYNAMIC]. An MPLS-TP network shall use the same PW signaling protocols and procedures for placing SS-PWs and MS-PWs. This will leverage existing technology as well as facilitate interoperability with client networks with native attachment circuits or PW segments that are switched across an MPLS-TP network.

Management-Plane Support

There is no MPLS-TP requirement for a standardized management interface to the MPLS-TP control plane. A general overview of MPLS- TP-related MIB modules can be found in [TP-MIB]. Network management requirements for MPLS-based transport networks are provided in RFC5951.

PW Control (LDP) and MPLS-TP Requirements Table

The following table shows how the MPLS-TP control-plane requirements can be met using the existing LDP control plane for pseudowires (targeted LDP). Areas where additional specifications are required are also identified. The table lists references based on the control-plane requirements as identified and numbered above in Section 2.

In the table below, several of the requirements shown are addressed -- in part or in full -- by the use of MPLS-TP LSPs to carry pseudowires. This is reflected by including "TP-LSPs" as a reference for those requirements. Section 5.3.2 provides additional context for the binding of PWs to TP-LSPs.

+=======+===========================================================+ | Req # | References | +-------+-----------------------------------------------------------+ | 1 | Generic requirement met by using Standards Track RFCs | | 2 | RFC3985, RFC4447, Together with TP-LSPs (Sec. 4.3) | | 3 | RFC3985, RFC4447 | | 4 | Generic requirement met by using Standards Track RFCs | | 5 | RFC3985, RFC4447, Together with TP-LSPs | | 6 | RFC3985, RFC4447, [PW-P2MPR], [PW-P2MPE] + TP-LSPs | | 7 | RFC3985, RFC4447, + TP-LSPs | | 8 | [PW-P2MPR], [PW-P2MPE] | | 9 | RFC3985, end-node only involvement for PW | | 10 | RFC3985, proper vendor implementation | | 11 | RFC3985, end-node only involvement for PW | | 12-13 | RFC3985, RFC4447, See Section 5.3.4 | | 14 | RFC3985, RFC4447 | | 15 | RFC4447, RFC3478, proper vendor implementation | | 16 | RFC3985, RFC4447 | | 17-18 | RFC3985, proper vendor implementation | | 19-26 | RFC3985, RFC4447, RFC5659, implementation | | 27 | RFC4448, RFC4816, RFC4618, RFC4619, RFC4553 | | | RFC4842, RFC5287 | | 28 | RFC3985 | | 29-31 | RFC3985, RFC4447 | | 32 | RFC3985, RFC4447, RFC5659, See Section 5.3.6 | | 33 | RFC4385, RFC4447, RFC5586 | | 34 | [PW-P2MPR], [PW-P2MPE] | | 35 | RFC4863 | | 36-37 | RFC3985, RFC4447, See Section 5.3.4 | | 38 | Provided by TP-LSPs | | 39 | RFC3985, RFC4447, + TP-LSPs | | 40 | RFC3478 | | 41-42 | RFC3985, RFC4447 | | 43-44 | RFC3985, RFC4447, + TP-LSPs - See Section 5.3.5 | | 45 | RFC3985, RFC4447, RFC5659 + TP-LSPs | | 46 | RFC3985, RFC4447, + TP-LSPs - See Section 5.3.3 | | 47 | [PW-RED], [PW-REDB] | | 48-49 | RFC3985, RFC4447, + TP-LSPs, implementation | | 50-52 | Provided by TP-LSPs, and Section 5.3.5 | | 53-55 | RFC3985, RFC4447, See Section 5.3.5 | | 56 | [PW-RED], [PW-REDB] | | | revertive/non-revertive behavior is a local matter for PW | | 57-58 | [PW-RED], [PW-REDB] | | 59-81 | RFC3985, RFC4447, [PW-RED], [PW-REDB], Section 5.3.5 | | 82-83 | RFC5085, RFC5586, RFC5885 | | 84-89 | RFC3985, RFC4447, [PW-RED], [PW-REDB], Section 5.3.5 | | 90-95 | RFC3985, RFC4447, + TP-LSPs, implementation | | 96 | RFC4447, [MS-PW-DYNAMIC] |

| 97 | RFC4447 | | 98 - | | | 99 | Not Applicable to PW | | 100 | RFC4447 | | 101 | RFC3478 | | 102 | RFC3985, + TP-LSPs | | 103 | Not Applicable to PW | | 104 | [PW-OAM] | | 105 | [PW-OAM] | | 106 - | | | 108 | RFC5085, RFC5586, RFC5885 | | 109 | RFC5085, RFC5586, RFC5885 | | | fault reporting and protection triggering is a local | | | matter for PW | | 110 | RFC5085, RFC5586, RFC5885 | | | fault reporting and protection triggering is a local | | | matter for PW | | 111 | RFC4447 | | 112 | RFC4447, RFC5085, RFC5586, RFC5885 | | 113 | RFC5085, RFC5586, RFC5885 | | 114 | RFC5085, RFC5586, RFC5885 | | 115 | path traversed by PW is determined by LSP path; see | | | GMPLS and MPLS-TP Requirements Table, Section 4.3 | | 116 | [PW-RED], [PW-REDB], administrative control of redundant | | | PW is a local matter at the PW head-end | | 117 | [PW-RED], [PW-REDB], RFC5085, RFC5586, RFC5885 | | 118 | RFC3985, RFC4447, [PW-RED], [PW-REDB], Section 5.3.5 | | 119 | RFC4447 | | 120 - | | | 125 | RFC5085, RFC5586, RFC5885 | | 126 - | | | 130 | [PW-OAM] | | 131 | Section 5.3.5 | | 132 | [PW-OAM] | | 133 | [PW-OAM] | | 134 | Section 5.3.5 | | 135 | [PW-OAM] | | 136 | Not Applicable to PW | | 137 | Not Applicable to PW | | 138 | RFC4447, RFC5003, [MS-PW-DYNAMIC] | | 139 - | | | 143 | [PW-OAM] | +=======+===========================================================+

     Table 2: PW Control (LDP) and MPLS-TP Requirements Table

Anticipated MPLS-TP-Related Extensions

Existing control protocol and procedures will be reused as much as possible to support MPLS-TP. However, when using PWs in MPLS-TP, a set of new requirements is defined that may require extensions of the existing control mechanisms. This section clarifies the areas where extensions are needed based on the requirements that are related to the PW control plane and documented in RFC5654.

Table 2 lists how requirements defined in RFC5654 are expected to be addressed.

The baseline requirement for extensions to support transport applications is that any new mechanisms and capabilities must be able to interoperate with existing IETF MPLS RFC3031 and IETF PWE3 RFC3985 control and data planes where appropriate. Hence, extensions of the PW control plane must be in-line with the procedures defined in RFC4447, RFC6073, and [MS-PW-DYNAMIC].

Extensions to Support Out-of-Band PW Control

For MPLS-TP, it is required that the data and control planes can be both logically and physically separated. That is, the PW control plane must be able to operate out-of-band (OOB). This separation ensures, among other things, that in the case of control-plane failures the data plane is not affected and can continue to operate normally. This was not a design requirement for the current PW control plane. However, due to the PW concept, i.e., PWs are connecting logical entities ('forwarders'), and the operation of the PW control protocol, i.e., only edge PE nodes (T-PE, S-PE) take part in the signaling exchanges: moving T-LDP out-of-band seems to be, theoretically, a straightforward exercise.

In fact, as a strictly local matter, ensuring that targeted LDP (T-LDP) uses out-of-band signaling requires only that the local implementation is configured in such a way that reachability for a target LSR address is via the out-of-band channel.

More precisely, if IP addressing is used in the MPLS-TP control plane, then T-LDP addressing can be maintained, although all addresses will refer to control-plane entities. Both the PWid Forwarding Equivalence Class (FEC) and Generalized PWid FEC Elements can possibly be used in an OOB case as well. (Detailed evaluation is outside the scope of this document.) The PW label allocation and exchange mechanisms should be reused without change.

Support for Explicit Control of PW-to-LSP Binding

Binding a PW to an LSP, or PW segments to LSPs, is left to nodes acting as T-PEs and S-PEs or a control-plane entity that may be the same one signaling the PW. However, an extension of the PW signaling protocol is required to allow the LSR at the signal initiation end to inform the targeted LSR (at the signal termination end) to which LSP the resulting PW is to be bound, in the event that more than one such LSP exists and the choice of LSPs is important to the service being setup (for example, if the service requires co-routed bidirectional paths). This is also particularly important to support transport path (symmetric and asymmetric) bandwidth requirements.

For transport services, MPLS-TP requires support for bidirectional traffic that follows congruent paths. Currently, each direction of a PW or a PW segment is bound to a unidirectional LSP that extends between two T-PEs, two S-PEs, or a T-PE and an S-PE. The unidirectional LSPs in both directions are not required to follow congruent paths, and therefore both directions of a PW may not follow congruent paths, i.e., they are associated bidirectional paths. The only requirement in RFC5659 is that a PW or a PW segment shares the same T-PEs in both directions and the same S-PEs in both directions.

MPLS-TP imposes new requirements on the PW control plane, in requiring that both end points map the PW or PW segment to the same transport path for the case where this is an objective of the service. When a bidirectional LSP is selected on one end to transport the PW, a mechanism is needed that signals to the remote end which LSP has been selected locally to transport the PW. This would be accomplished by adding a new TLV to PW signaling.

Note that this coincides with the gap identified for OOB support: a new mechanism is needed to allow explicit binding of a PW to the supporting transport LSP.

The case of unidirectional transport paths may also require additional protocol mechanisms, as today's PWs are always bidirectional. One potential approach for providing a unidirectional PW-based transport path is for the PW to associate different (asymmetric) bandwidths in each direction, with a zero or minimal bandwidth for the return path. This approach is consistent with Section 3.8.2 of RFC5921 but does not address P2MP paths.

Support for Dynamic Transfer of PW Control/Ownership

In order to satisfy requirement 47 (as defined in Section 2), it will be necessary to specify methods for transfer of PW ownership from the management to the control plane (and vice versa).

Interoperable Support for PW/LSP Resource Allocation

Transport applications may require resource guarantees. For such transport LSPs, resource reservation mechanisms are provided via RSVP-TE and the use of Diffserv. If multiple PWs are multiplexed into the same transport LSP resources, contention may occur. However, local policy at PEs should ensure proper resource sharing among PWs mapped into a resource-guaranteed LSP. In the case of MS-PWs, signaling carries the PW traffic parameters [MS-PW-DYNAMIC] to enable admission control of a PW segment over a resource- guaranteed LSP.

In conjunction with explicit PW-to-LSP binding, existing mechanisms may be sufficient; however, this needs to be verified in detailed evaluation.

Support for PW Protection and PW OAM Configuration

Many of the requirements listed in Section 2 are intended to support connectivity and performance monitoring (grouped together as OAM), as well as protection conformant with the transport services model.

In general, protection of MPLS-TP transported services is provided by way of protection of transport LSPs. PW protection requires that mechanisms be defined to support redundant pseudowires, including a mechanism already described above for associating such pseudowires with specific protected ("working" and "protection") LSPs. Also required are definitions of local protection control functions, to include test/verification operations, and protection status signals needed to ensure that PW termination points are in agreement as to which of a set of redundant pseudowires are in use for which transport services at any given point in time.

Much of this work is currently being done in documents [PW-RED] and [PW-REDB] that define, respectively, how to establish redundant pseudowires and how to indicate which is in use. Additional work may be required.

Protection switching may be triggered manually by the operator, or as a result of loss of connectivity (detected using the mechanisms of RFC5085 and RFC5586), or service degradation (detected using mechanisms yet to be defined).

Automated protection switching is just one of the functions for which a transport service requires OAM. OAM is generally referred to as either "proactive" or "on-demand", where the distinction is whether a specific OAM tool is being used continuously over time (for the purpose of detecting a need for protection switching, for example) or

is only used -- either a limited number of times or over a short period of time -- when explicitly enabled (for diagnostics, for example).

PW OAM currently consists of connectivity verification defined by RFC5085. Work is currently in progress to extend PW OAM to include bidirectional forwarding detection (BFD) in RFC5885, and work has begun on extending BFD to include performance-related monitor functions.

Client-Layer and Cross-Provider Interfaces to PW Control

Additional work is likely to be required to define consistent access by a client-layer network, as well as between provider networks, to control information available to each type of network, for example, about the topology of an MS-PW. This information may be required by the client-layer network in order to provide hints that may help to avoid establishment of fate-sharing alternate paths. Such work will need to fit within the ASON architecture; see requirement 38 above.

ASON Architecture Considerations

MPLS-TP PWs are always transported using LSPs, and these LSPs will either have been statically provisioned or signaled using GMPLS.

For LSPs signaled using the MPLS-TP LSP control plane (GMPLS), conformance with the ASON architecture is as described in Section 1.2 ("Basic Approach"), bullet 4, of this framework document.

As discussed above in Section 5.3, there are anticipated extensions in the following areas that may be related to ASON architecture:

  - PW-to-LSP binding (Section 5.3.2)
  - PW/LSP resource allocation (Section 5.3.4)
  - PW protection and OAM configuration (Section 5.3.5)
  - Client-layer interfaces for PW control (Section 5.3.6)

This work is expected to be consistent with ASON architecture and may require additional specification in order to achieve this goal.

Security Considerations

This document primarily describes how existing mechanisms can be used to meet the MPLS-TP control-plane requirements. The documents that describe each mechanism contain their own security considerations sections. For a general discussion on MPLS- and GMPLS-related

security issues, see the MPLS/GMPLS security framework RFC5920. As mentioned above in Section 2.4, there are no specific MPLS-TP control-plane security requirements.

This document also identifies a number of needed control-plane extensions. It is expected that the documents that define such extensions will also include any appropriate security considerations.

Acknowledgments

The authors would like to acknowledge the contributions of Yannick Brehon, Diego Caviglia, Nic Neate, Dave Mcdysan, Dan Frost, and Eric Osborne to this work. We also thank Dan Frost in his help responding to Last Call comments.

References

Normative References

RFC2210 Wroclawski, J., "The Use of RSVP with IETF Integrated

          Services", RFC 2210, September 1997.

RFC2211 Wroclawski, J., "Specification of the Controlled-Load

          Network Element Service", RFC 2211, September 1997.

RFC2212 Shenker, S., Partridge, C., and R. Guerin, "Specification

          of Guaranteed Quality of Service", RFC 2212, September
          1997.

RFC3031 Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol

          Label Switching Architecture", RFC 3031, January 2001.

RFC3209 Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,

          and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
          Tunnels", RFC 3209, December 2001.

RFC3471 Berger, L., Ed., "Generalized Multi-Protocol Label

          Switching (GMPLS) Signaling Functional Description", RFC
          3471, January 2003.

RFC3473 Berger, L., Ed., "Generalized Multi-Protocol Label

          Switching (GMPLS) Signaling Resource ReserVation Protocol-
          Traffic Engineering (RSVP-TE) Extensions", RFC 3473,
          January 2003.

RFC3478 Leelanivas, M., Rekhter, Y., and R. Aggarwal, "Graceful

          Restart Mechanism for Label Distribution Protocol", RFC
          3478, February 2003.

RFC3630 Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering

          (TE) Extensions to OSPF Version 2", RFC 3630, September
          2003.

RFC4124 Le Faucheur, F., Ed., "Protocol Extensions for Support of

          Diffserv-aware MPLS Traffic Engineering", RFC 4124, June
          2005.

RFC4202 Kompella, K., Ed., and Y. Rekhter, Ed., "Routing

          Extensions in Support of Generalized Multi-Protocol Label
          Switching (GMPLS)", RFC 4202, October 2005.

RFC4203 Kompella, K., Ed., and Y. Rekhter, Ed., "OSPF Extensions

          in Support of Generalized Multi-Protocol Label Switching
          (GMPLS)", RFC 4203, October 2005.

RFC4206 Kompella, K. and Y. Rekhter, "Label Switched Paths (LSP)

          Hierarchy with Generalized Multi-Protocol Label Switching
          (GMPLS) Traffic Engineering (TE)", RFC 4206, October 2005.

RFC4385 Bryant, S., Swallow, G., Martini, L., and D. McPherson,

          "Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for
          Use over an MPLS PSN", RFC 4385, February 2006.

RFC4447 Martini, L., Ed., Rosen, E., El-Aawar, N., Smith, T., and

          G. Heron, "Pseudowire Setup and Maintenance Using the
          Label Distribution Protocol (LDP)", RFC 4447, April 2006.

RFC4448 Martini, L., Ed., Rosen, E., El-Aawar, N., and G. Heron,

          "Encapsulation Methods for Transport of Ethernet over MPLS
          Networks", RFC 4448, April 2006.

RFC4842 Malis, A., Pate, P., Cohen, R., Ed., and D. Zelig,

          "Synchronous Optical Network/Synchronous Digital Hierarchy
          (SONET/SDH) Circuit Emulation over Packet (CEP)", RFC
          4842, April 2007.

RFC4863 Martini, L. and G. Swallow, "Wildcard Pseudowire Type",

          RFC 4863, May 2007.

RFC4872 Lang, J., Ed., Rekhter, Y., Ed., and D. Papadimitriou,

          Ed., "RSVP-TE Extensions in Support of End-to-End
          Generalized Multi-Protocol Label Switching (GMPLS)
          Recovery", RFC 4872, May 2007.

RFC4873 Berger, L., Bryskin, I., Papadimitriou, D., and A. Farrel,

          "GMPLS Segment Recovery", RFC 4873, May 2007.

RFC4929 Andersson, L., Ed., and A. Farrel, Ed., "Change Process

          for Multiprotocol Label Switching (MPLS) and Generalized
          MPLS (GMPLS) Protocols and Procedures", BCP 129, RFC 4929,
          June 2007.

RFC4974 Papadimitriou, D. and A. Farrel, "Generalized MPLS (GMPLS)

          RSVP-TE Signaling Extensions in Support of Calls", RFC
          4974, August 2007.

RFC5063 Satyanarayana, A., Ed., and R. Rahman, Ed., "Extensions to

          GMPLS Resource Reservation Protocol (RSVP) Graceful
          Restart", RFC 5063, October 2007.

RFC5151 Farrel, A., Ed., Ayyangar, A., and JP. Vasseur, "Inter-

          Domain MPLS and GMPLS Traffic Engineering -- Resource
          Reservation Protocol-Traffic Engineering (RSVP-TE)
          Extensions", RFC 5151, February 2008.

RFC5287 Vainshtein, A. and Y(J). Stein, "Control Protocol

          Extensions for the Setup of Time-Division Multiplexing
          (TDM) Pseudowires in MPLS Networks", RFC 5287, August
          2008.

RFC5305 Li, T. and H. Smit, "IS-IS Extensions for Traffic

          Engineering", RFC 5305, October 2008.

RFC5307 Kompella, K., Ed., and Y. Rekhter, Ed., "IS-IS Extensions

          in Support of Generalized Multi-Protocol Label Switching
          (GMPLS)", RFC 5307, October 2008.

RFC5316 Chen, M., Zhang, R., and X. Duan, "ISIS Extensions in

          Support of Inter-Autonomous System (AS) MPLS and GMPLS
          Traffic Engineering", RFC 5316, December 2008.

RFC5392 Chen, M., Zhang, R., and X. Duan, "OSPF Extensions in

          Support of Inter-Autonomous System (AS) MPLS and GMPLS
          Traffic Engineering", RFC 5392, January 2009.

RFC5467 Berger, L., Takacs, A., Caviglia, D., Fedyk, D., and J.

          Meuric, "GMPLS Asymmetric Bandwidth Bidirectional Label
          Switched Paths (LSPs)", RFC 5467, March 2009.

RFC5586 Bocci, M., Ed., Vigoureux, M., Ed., and S. Bryant, Ed.,

          "MPLS Generic Associated Channel", RFC 5586, June 2009.

RFC5654 Niven-Jenkins, B., Ed., Brungard, D., Ed., Betts, M., Ed.,

          Sprecher, N., and S. Ueno, "Requirements of an MPLS
          Transport Profile", RFC 5654, September 2009.

RFC5860 Vigoureux, M., Ed., Ward, D., Ed., and M. Betts, Ed.,

          "Requirements for Operations, Administration, and
          Maintenance (OAM) in MPLS Transport Networks", RFC 5860,
          May 2010.

RFC5921 Bocci, M., Ed., Bryant, S., Ed., Frost, D., Ed., Levrau,

          L., and L. Berger, "A Framework for MPLS in Transport
          Networks", RFC 5921, July 2010.

RFC5960 Frost, D., Ed., Bryant, S., Ed., and M. Bocci, Ed., "MPLS

          Transport Profile Data Plane Architecture", RFC 5960,
          August 2010.

RFC6370 Bocci, M., Swallow, G., and E. Gray, "MPLS Transport

          Profile (MPLS-TP) Identifiers", RFC 6370, September 2011.

RFC6371 Busi, I., Ed., and D. Allan, Ed., "Operations,

          Administration, and Maintenance Framework for MPLS-Based
          Transport Networks", RFC 6371, September 2011.

RFC6372 Sprecher, N., Ed., and A. Farrel, Ed., "MPLS Transport

          Profile (MPLS-TP) Survivability Framework", RFC 6372,
          September 2011.

Informative References

[CCAMP-OAM-EXT]

          Bellagamba, E., Ed., Andersson, L., Ed., Skoldstrom, P.,
          Ed., Ward, D., and A. Takacs, "Configuration of Pro-Active
          Operations, Administration, and Maintenance (OAM)
          Functions for MPLS-based Transport Networks using RSVP-
          TE", Work in Progress, July 2011.

[CCAMP-OAM-FWK]

          Takacs, A., Fedyk, D., and J. He, "GMPLS RSVP-TE
          extensions for OAM Configuration", Work in Progress, July
          2011.

[GMPLS-PS] Takacs, A., Fondelli, F., and B. Tremblay, "GMPLS RSVP-TE

          Recovery Extension for data plane initiated reversion and
          protection timer signalling", Work in Progress, April
          2011.

[ITU.G8080.2006]

          International Telecommunication Union, "Architecture for
          the automatically switched optical network (ASON)", ITU-T
          Recommendation G.8080, June 2006.

[ITU.G8080.2008]

          International Telecommunication Union, "Architecture for
          the automatically switched optical network (ASON)
          Amendment 1", ITU-T Recommendation G.8080 Amendment 1,
          March 2008.

[MS-PW-DYNAMIC]

          Martini, L., Ed., Bocci, M., Ed., and F. Balus, Ed.,
          "Dynamic Placement of Multi Segment Pseudowires", Work in
          Progress, July 2011.

[NO-PHP] Ali, z., et al, "Non Penultimate Hop Popping Behavior and

          out-of-band mapping for RSVP-TE Label Switched Paths",
          Work in Progress, August 2011.

[PW-OAM] Zhang, F., Ed., Wu, B., Ed., and E. Bellagamba, Ed., "

          Label Distribution Protocol Extensions for Proactive
          Operations, Administration and Maintenance Configuration
          of Dynamic MPLS Transport Profile PseudoWire", Work in
          Progress, August 2011.

[PW-P2MPE] Aggarwal, R. and F. Jounay, "Point-to-Multipoint Pseudo-

          Wire Encapsulation", Work in Progress, March 2010.

[PW-P2MPR] Jounay, F., Ed., Kamite, Y., Heron, G., and M. Bocci,

          "Requirements and Framework for Point-to-Multipoint
          Pseudowire", Work in Progress, July 2011.

[PW-RED] Muley, P., Ed., Aissaoui, M., Ed., and M. Bocci,

          "Pseudowire Redundancy", Work in Progress, July 2011.

[PW-REDB] Muley, P., Ed., and M. Aissaoui, Ed., "Preferential

          Forwarding Status Bit", Work in Progress, March 2011.

RFC3270 Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen,

          P., Krishnan, R., Cheval, P., and J. Heinanen, "Multi-
          Protocol Label Switching (MPLS) Support of Differentiated
          Services", RFC 3270, May 2002.

RFC3468 Andersson, L. and G. Swallow, "The Multiprotocol Label

          Switching (MPLS) Working Group decision on MPLS signaling
          protocols", RFC 3468, February 2003.

RFC3472 Ashwood-Smith, P., Ed., and L. Berger, Ed., "Generalized

          Multi-Protocol Label Switching (GMPLS) Signaling
          Constraint-based Routed Label Distribution Protocol (CR-
          LDP) Extensions", RFC 3472, January 2003.

RFC3477 Kompella, K. and Y. Rekhter, "Signalling Unnumbered Links

          in Resource ReSerVation Protocol - Traffic Engineering
          (RSVP-TE)", RFC 3477, January 2003.

RFC3812 Srinivasan, C., Viswanathan, A., and T. Nadeau,

          "Multiprotocol Label Switching (MPLS) Traffic Engineering
          (TE) Management Information Base (MIB)", RFC 3812, June
          2004.

RFC3813 Srinivasan, C., Viswanathan, A., and T. Nadeau,

          "Multiprotocol Label Switching (MPLS) Label Switching
          Router (LSR) Management Information Base (MIB)", RFC 3813,
          June 2004.

RFC3945 Mannie, E., Ed., "Generalized Multi-Protocol Label

          Switching (GMPLS) Architecture", RFC 3945, October 2004.

RFC3985 Bryant, S., Ed., and P. Pate, Ed., "Pseudo Wire Emulation

          Edge-to-Edge (PWE3) Architecture", RFC 3985, March 2005.

RFC4139 Papadimitriou, D., Drake, J., Ash, J., Farrel, A., and L.

          Ong, "Requirements for Generalized MPLS (GMPLS) Signaling
          Usage and Extensions for Automatically Switched Optical
          Network (ASON)", RFC 4139, July 2005.

RFC4201 Kompella, K., Rekhter, Y., and L. Berger, "Link Bundling

          in MPLS Traffic Engineering (TE)", RFC 4201, October 2005.

RFC4208 Swallow, G., Drake, J., Ishimatsu, H., and Y. Rekhter,

          "Generalized Multiprotocol Label Switching (GMPLS) User-
          Network Interface (UNI): Resource ReserVation Protocol-
          Traffic Engineering (RSVP-TE) Support for the Overlay
          Model", RFC 4208, October 2005.

RFC4258 Brungard, D., Ed., "Requirements for Generalized Multi-

          Protocol Label Switching (GMPLS) Routing for the
          Automatically Switched Optical Network (ASON)", RFC 4258,
          November 2005.

RFC4379 Kompella, K. and G. Swallow, "Detecting Multi-Protocol

          Label Switched (MPLS) Data Plane Failures", RFC 4379,
          February 2006.

RFC4426 Lang, J., Ed., Rajagopalan, B., Ed., and D. Papadimitriou,

          Ed., "Generalized Multi-Protocol Label Switching (GMPLS)
          Recovery Functional Specification", RFC 4426, March 2006.

RFC4427 Mannie, E., Ed., and D. Papadimitriou, Ed., "Recovery

          (Protection and Restoration) Terminology for Generalized
          Multi-Protocol Label Switching (GMPLS)", RFC 4427, March
          2006.

RFC4553 Vainshtein, A., Ed., and YJ. Stein, Ed., "Structure-

          Agnostic Time Division Multiplexing (TDM) over Packet
          (SAToP)", RFC 4553, June 2006.

RFC4618 Martini, L., Rosen, E., Heron, G., and A. Malis,

          "Encapsulation Methods for Transport of PPP/High-Level
          Data Link Control (HDLC) over MPLS Networks", RFC 4618,
          September 2006.

RFC4619 Martini, L., Ed., Kawa, C., Ed., and A. Malis, Ed.,

          "Encapsulation Methods for Transport of Frame Relay over
          Multiprotocol Label Switching (MPLS) Networks", RFC 4619,
          September 2006.

RFC4655 Farrel, A., Vasseur, J.-P., and J. Ash, "A Path

          Computation Element (PCE)-Based Architecture", RFC 4655,
          August 2006.

RFC4783 Berger, L., Ed., "GMPLS - Communication of Alarm

          Information", RFC 4783, December 2006.

RFC4802 Nadeau, T., Ed., and A. Farrel, Ed., "Generalized

          Multiprotocol Label Switching (GMPLS) Traffic Engineering
          Management Information Base", RFC 4802, February 2007.

RFC4803 Nadeau, T., Ed., and A. Farrel, Ed., "Generalized

          Multiprotocol Label Switching (GMPLS) Label Switching
          Router (LSR) Management Information Base", RFC 4803,
          February 2007.

RFC4816 Malis, A., Martini, L., Brayley, J., and T. Walsh,

          "Pseudowire Emulation Edge-to-Edge (PWE3) Asynchronous
          Transfer Mode (ATM) Transparent Cell Transport Service",
          RFC 4816, February 2007.

RFC4875 Aggarwal, R., Ed., Papadimitriou, D., Ed., and S.

          Yasukawa, Ed., "Extensions to Resource Reservation
          Protocol - Traffic Engineering (RSVP-TE) for Point-to-
          Multipoint TE Label Switched Paths (LSPs)", RFC 4875, May
          2007.

RFC5003 Metz, C., Martini, L., Balus, F., and J. Sugimoto,

          "Attachment Individual Identifier (AII) Types for
          Aggregation", RFC 5003, September 2007.

RFC5036 Andersson, L., Ed., Minei, I., Ed., and B. Thomas, Ed.,

          "LDP Specification", RFC 5036, October 2007.

RFC5085 Nadeau, T., Ed., and C. Pignataro, Ed., "Pseudowire

          Virtual Circuit Connectivity Verification (VCCV): A
          Control Channel for Pseudowires", RFC 5085, December 2007.

RFC5145 Shiomoto, K., Ed., "Framework for MPLS-TE to GMPLS

          Migration", RFC 5145, March 2008.

RFC5440 Vasseur, JP., Ed., and JL. Le Roux, Ed., "Path Computation

          Element (PCE) Communication Protocol (PCEP)", RFC 5440,
          March 2009.

RFC5493 Caviglia, D., Bramanti, D., Li, D., and D. McDysan,

          "Requirements for the Conversion between Permanent
          Connections and Switched Connections in a Generalized
          Multiprotocol Label Switching (GMPLS) Network", RFC 5493,
          April 2009.

RFC5659 Bocci, M. and S. Bryant, "An Architecture for Multi-

          Segment Pseudowire Emulation Edge-to-Edge", RFC 5659,
          October 2009.

RFC5787 Papadimitriou, D., "OSPFv2 Routing Protocols Extensions

          for Automatically Switched Optical Network (ASON)
          Routing", RFC 5787, March 2010.

RFC5852 Caviglia, D., Ceccarelli, D., Bramanti, D., Li, D., and S.

          Bardalai, "RSVP-TE Signaling Extension for LSP Handover
          from the Management Plane to the Control Plane in a GMPLS-
          Enabled Transport Network", RFC 5852, April 2010.

RFC5884 Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow,

          "Bidirectional Forwarding Detection (BFD) for MPLS Label
          Switched Paths (LSPs)", RFC 5884, June 2010.

RFC5885 Nadeau, T., Ed., and C. Pignataro, Ed., "Bidirectional

          Forwarding Detection (BFD) for the Pseudowire Virtual
          Circuit Connectivity Verification (VCCV)", RFC 5885, June
          2010.

RFC5920 Fang, L., Ed., "Security Framework for MPLS and GMPLS

          Networks", RFC 5920, July 2010.

RFC5951 Lam, K., Mansfield, S., and E. Gray, "Network Management

          Requirements for MPLS-based Transport Networks", RFC 5951,
          September 2010.

RFC6001 Papadimitriou, D., Vigoureux, M., Shiomoto, K., Brungard,

          D., and JL. Le Roux, "Generalized MPLS (GMPLS) Protocol
          Extensions for Multi-Layer and Multi-Region Networks
          (MLN/MRN)", RFC 6001, October 2010.

RFC6073 Martini, L., Metz, C., Nadeau, T., Bocci, M., and M.

          Aissaoui, "Segmented Pseudowire", RFC 6073, January 2011.

RFC6107 Shiomoto, K., Ed., and A. Farrel, Ed., "Procedures for

          Dynamically Signaled Hierarchical Label Switched Paths",
          RFC 6107, February 2011.

RFC6215 Bocci, M., Levrau, L., and D. Frost, "MPLS Transport

          Profile User-to-Network and Network-to-Network
          Interfaces", RFC 6215, April 2011.

[TE-MIB] Miyazawa, M., Otani, T., Kumaki, K., and T. Nadeau,

          "Traffic Engineering Database Management Information Base
          in support of MPLS-TE/GMPLS", Work in Progress, July 2011.

[TP-MIB] King, D., Ed., and M. Venkatesan, Ed., "Multiprotocol

          Label Switching Transport Profile (MPLS-TP) MIB-based
          Management Overview", Work in Progress, August 2011.

[TP-P2MP-FWK]

          Frost, D., Ed., Bocci, M., Ed., and L. Berger, Ed., "A
          Framework for Point-to-Multipoint MPLS in Transport
          Networks", Work in Progress, July 2011.

[TP-RING] Weingarten, Y., Ed., "MPLS-TP Ring Protection", Work in

          Progress, June 2011

Contributing Authors

Attila Takacs Ericsson 1. Laborc u. Budapest 1037 HUNGARY EMail: [email protected]

Martin Vigoureux Alcatel-Lucent EMail: [email protected]

Elisa Bellagamba Ericsson Farogatan, 6 164 40, Kista, Stockholm SWEDEN EMail: [email protected]

Authors' Addresses

Loa Andersson (editor) Ericsson Phone: +46 10 717 52 13 EMail: [email protected]

Lou Berger (editor) LabN Consulting, L.L.C. Phone: +1-301-468-9228 EMail: [email protected]

Luyuan Fang (editor) Cisco Systems, Inc. 111 Wood Avenue South Iselin, NJ 08830 USA EMail: [email protected]

Nabil Bitar (editor) Verizon 60 Sylvan Road Waltham, MA 02451 USA EMail: [email protected]

Eric Gray (editor) Ericsson 900 Chelmsford Street Lowell, MA 01851 USA Phone: +1 978 275 7470 EMail: [email protected]